Ultra Custom Pools

Item Category: Heating & Cooling: Parts & Accessories

Epifanes Wood Finish Gloss (1000 ml) 1000 ml

High gloss beauty with outstanding U.V. protection for teak and other fine hardwoods. High build, hard finish without sanding between coats. One component varnish based on phenolic-modified alkyd resin and tung oil.

Professional concrete floor finish high gloss 1 Gal quick drying acrylic (520)

Normal 0 false false false EN-US JA X-NONE UBQ Industries – Active Elements™ Advance Protect and Shine Acrylic Floor Finish Active Elements™ – Protect & Shine is a high gloss long lasting and renewable maintenance coat for interior decorative concrete floors. Protect & Shine is a rapid return to service product making it ideal for retail and commercial floors where maintenance must be performed during after hours. It is also perfect for residential floors especially when there are pets present or the floors get heavy use. Active Elements™ – Protect & Shine should be applied over the top of a base sealer such as Active Elements™ – Advance Seal. Coverage 500 – 1000 square feet per gallon Coverage variations depend on concrete surface porosity and amount of material applied. Drying Time Dry to Touch. 5-15 minutes Recoat 30 minutes Light traffic 1 hour Full Cure 5 hours Surface PreparationPrior to the application of Active Elements – Protect & Shine, the floor must be clean and dry. A previously applied base sealer must be fully cured. Application Tools Finish mop or floor finish applicator. Application Completely dampen the finish applicator with Active Elements – Protect & Shine and apply a very thin coat. As Active Elements – Protect & Shine is being applied it should make the floor look wet but not milky. If you are seeing a milky haze, reduce the amount of material being applied per square foot. Each successive coat should be applied perpendicular to the previous coat in order to reduce lap marks. ***For interior use only.*** Initial application on a floor — apply 4-8 thin coats. As a maintenance application — apply 1-2 thin coats. Thinning Do not thin. Clean Up Tools can be cleaned with soap and water. Storage and Shelf Life Do not allow to freeze. Shelf life of unopened product is approximately one year. Slip and Fall Precautions Water or other foreign substances will cause a floor coated with Floor Finish to become slippery. ALWAYS use a “Wet Floor” sign when moisture is present. Safety Do not breathe vapors. When using in confined or limited ventilation areas, use appropriate respirator to protect against breathing vapors. Avoid contact with skin; wear protective gloves and clothing. Always use eye protection such as goggles, face shield or safety glasses. Read Material Safety Data Sheet before using. First Aid Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids open. Seek medical attention. Skin Contact: Immediately remove contaminated clothing. Wipe excess from skin and wash with soap and water. Seek medical attention if irritation persists. Inhalation: Remove person to fresh air and provide oxygen if breathing is difficult. Seek medical attention. Moisture Vapor Emissions / Alkalinity Precautions All interior concrete floors not poured over an effective moisture vapor barrier/inhibitor are subject to possible moisture vapor transmission and related high levels of alkalinity that may lead to blistering and failure of the coating system. It is the coating applicator’s responsibility to conduct calcium chloride and relative humidity probe testing to determine if excessive levels of vapor emissions or alkalinity are present before applying any coatings. Warranty This warranty is made in lieu of all other warranties, either expressed or implied. Before application the User shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to replace said product. Any claim of defective product must be received in writing within one (1) year from date of shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from use of this product. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.

Watco 65851 Danish Oil Wood Finish, Pint, Dark Walnut

Watco Pint Dark Walnut Danish Oil Finish. Watco Danish Oil Wood Finish stains, seals, and protects in one easy step to produce a warm, natural hand rubbed appearance. Oil-based formula of blended oil & varnish penetrates deeply into wood pores for ultimate protection.

OSMO UV Protection Oil Satin Exterior Water Repellent Wood Finish Stain EXTRA

OSMO UV Protection Oil EXTRA Wood finish for exterior useNatural oil-wax based-microporous2 in 1 – base and top coat in oneCoating protected against mold, algae and fungal attackFor vertical surfaces Coverage Rate 0.125L – 28 square feetCoverage Rate 0.75L – 140 square feetCoverage Rate 2.5L – 480 square feet

HOWARD RF6016 Restor-A-Finish, 16 oz, Dark Walnut 16

The key was to develop a formula that could clean and polish the surface, penetrate the finish with stain, and leave the original finish intact. For over 40 years, Howard’s Restor-A-Finish has been a standard in the antique industry.

Howard Restor-A-Finish

Restores Color To Faded Wood FinishesBlends Out Scratches & BlemishesRemoves White Heat Rings Howard Restor-A-Finish Restor-A-Finish is a unique finish-penetrating formula that restores the original color and luster to your finish while blending out the blemishes and minor scratches. Restor-A-Finish restores the finish in one step – without removing any of the existing finish. Restore It – Don’t Strip It! With a simple wipe-on, wipe-off process, most finished wood surfaces that seem to need a refinishing job can be completely restored in a few minutes. White heat rings and water marks, sun fade, oxidation, smoke damage, and most other blemishes can be quickly eliminated. Before you go to the extreme of stripping it, try restoring it! Restor-A-Finish is available in nine colors: Neutral, Maple-Pine, Golden Oak, Cherry, Walnut, Mahogany, Dark Walnut, Dark Oak, and Ebony Brown. – And We Carry All The Colors! Treat Scratches, Nicks, and Abrasions Restor-A-Finish works best when applied with a small pad of toweling, or for severe white rings and crazing, with Super Fine(0000) steel wool. DO NOT pour directly on the finish. When using steel wool, always rub with the grain of the wood. First, determine the pressure you should use on an inconspicuous spot, as the hardness of finishes vary. Revive Wood Finishes Wipe on the appropriate color of Restor-A-Finish with a clean cloth. Let it stand for a few minutes then wipe dry. If you desire a slightly darker shade, simply apply a darker color of Restor-A-Finish. White Heat Rings and Water Marks Apply Restor-A-Finish (see above) with steel wool and rub hard enough with the grain of the wood to blend out the white effect. If high gloss finish should appear dull due to the use of steel wool, polish it out with a Howard Polishing Compound or Burnishing Cream. Raised and Blistered Finishes Apply Neutral Restor-A-Finish (to prevent darkening of wood beyond temporary “wet effect”) with steel wool. As blisters soften press down while the Restor-A-Finish is applied. Wipe dry, and again later if the surface “blooms” with excess Restor-A-Finish. Restore Minor Crazed or Checked Finishes Apply Restor-A-Finish with Fine Grade(000) steel wool. Rub hard enough to smooth out the finish, periodically checking your progress. Checked or crazed surfaces may absorb an excess of Restor-A-Finish and “bloom out” requiring another wiping later. Treat Carved Wood Restor-A-Finish has saved many hours of labor by restoring the finish on carved portions of furniture and clocks. Simply apply Restor-A-Finish with a small paint brush or soft tooth brush and wipe off.