Ultra Custom Pools

Item Tag: 10 Gauge Copper

10 AWG Solar Panel Wire 100′ Power Cable UL 4703 Copper MADE IN USA PV Gauge Red

Visit Our Store Solar Wire TEMCo ID: SW0018 Color: Red Conductor size: 10 AWG Length: 100 ft Feet per pound: 17.54 Nominal outside diameter (in.): 0.230 Conductor stranding: 19 strands per conductor Conductor material: Bare copper Insulation material: Cross linked Polyethylene (XLPEE) Max. amps per conductor: 40 A Max. voltage: 600 V Min. temperature rating: – 40°C Max. temperature rating: 90°C Approvals: Type USE-2 per UL 854, RHH/RHW-2 per UL 44, Type PV per UL 4703 Applications: Solar panels, DC circuits, inverter wiring data sheet Download the full specs. 11 Months From Now… If it doesn’t fit. If it looks funny. Or you just changed your mind. Even if it’s opened, used or broken, we will still accept your return and pay shipping both ways. No restocking fee. Up to 1 year. Free Shipping To Lower 48 States UL 4703 Cable vs. Other Types of Cable What makes UL 4703 a better choice than some other common cable ratings, such as THHN or USE-2? Overview The term “PV wire” (photovoltaic wire) is often used to refer to USE-2 or THHN wire, the terms are not interchangeable. PV wire is specifically rated in accordance with UL 4703. THHN wire is used as general building wire and lacks the construction and strength of specialized cables designated as UL 4703 or USE-2. Using THHN cable in place of either UL 4703 or USE-2 will result in failures. Though USE-2 wire is impact and crush resistant, UL 4703 rated cable is superior to USE-2 in regards to low temperature flexibility, sunlight resistance, and flame resistance. PV wire for solar panels also has a thicker jacket and insulation than USE-2 wire. USE-2 cable is used in grounded PV systems only, which UL 4703 cable can be used for both grounded and ungrounded arrays. View the quick comparison chart below for an overview. UL 4703 (PV Wire) Applications: Wiring solar panels. Underground service entrance wire for both grounded and ungrounded PV arrays.General purpose wiring for installation in conduit. Min. conductor size: 18 AWG Insulation: Cross-linked Polyethylene (XLPEE) Jacket: May or may not have jacket Temp rating: 90°C Wet, 150°C Dry Max Voltage: 600, 1000, or 2000 V Resistant to: Sunlight, ozone, UV, flame, moisture Flexibility at low temperatures: Higher Standards: Type USE-2 per UL 854 RHH/RHW-2 per UL 44 Type PV per UL 4703 THHN (Building Wire) Applications: General purpose wiring for installation in conduit. May also be used in machine tool, appliance and control circuit wiring. Cannot replace PV or USE-2 if standards require it. Min. conductor size: 14 AWG Insulation: Polyvinylchloride (PVC) Jacket: Nylon Temp rating: 75°C Oil, 75°C Wet, 90° Dry Max Voltage: 600 V Resistant to: Gasoline and oil Flexibility at low temperatures: Lower Standards: UL 83 & 1063 as Type THHN Wire 90°C in dry locations. Type THWN Wire 75°C in wet locations. A-A-59544, NEMA WC-5, UL-758 USE-2 (RHH/RHW Wire) Applications: Aerial, raceway, or direct burial. For connecting PV modules. Grounded PV arrays only. Min. conductor size: 14 AWG Insulation: Cross-linked Polyethylene (XLPEE) Jacket: May or may not have jacket Temp rating: 90°C Wet and Dry Max Voltage: 600 V Resistant to: Crushing and impact, sunlight Flexibility at low temperatures: Lower Standards: UL 44 for rubber covered wire. UL 854 for service entrance cable. Federal Govt. Specificiation J-C-30A, ASTM-B-3 (solid copper conductors), ASTM-B-3 and 6 (standard conductors) Applications Per the National Electrical Code, USE-2 wire is suitable for use in grounded PV arrays only. UL 4703 cable can be used within both grounded and ungrounded PV arrays. THHN cable is used as general building wire and cannot replace USE-2 or UL 4703 cable. Temperature Rating PV cable is rated for 90°C in wet conditions and up to 150°C in dry conditions. USE-2 is rated for 90°C in both wet and dry conditions. THHN cable is rated at 75°C in wet conditions and 90°C in dry conditions. Voltage PV wire can be rated for 600 V, 1000 V, or 2000 V. THHN and USE-2 wire are only rated for 600 V. Flexibility PV wire is made up of stranded copper conductors, which makes it flexible. USE-2 wire is usually installed in locations where it is not subject to movement or mechanical damage, so they can use either solid or stranded conductors made of copper, copper-clad aluminum, or aluminum, making it less flexible than PV wire. Insulation and Jacket Both PV and USE-2 cable use thermoset insulation and jacket, typically XLPEEE (cross-linked polyethylene) or EPCV. Testing Requirements USE-2 cable is usually installed underground where it will likely not encounter flames, while PV wire can be exposed in an installation, so flames tests are required only for PV wire. Overload and mechanical abuse tests (including crushing and impact resistance) are applicable only to USE-2 cable. PV wire must pass more stringent testing requirements for sunlight resistance and low temperature flexibility. It undergoes a 720 hour weatherometer and a -40°C cold chamber conditioning. In contrast, the requirements for USE-2 cable are 300-hour weatherometer and -25°C cold chamber conditioning. Features Resistant to sunlight, ozone, UV, flame, and moisture. Proudly Made in the U.S.A. ZERO WIRE IMPORTS POLICY. We have a Physical Location. If you have questions, we want to hear from you. Wanna talk or pick up your order? Stop by! We’d be glad to have you. Best Price/Quality Guaranteed! We pass on our buying power with low prices. Excellent Quality Guaranteed! Give us a call or drop by, and we’ll show you. As an OEM, we use many of the products we sell. As a result, only high quality materials are offered to you. Get it FAST. Most orders received in 2 to 5 days. Our return policy. If you don’t like it, we’ll take it back and pay the shipping! Other Solar Hardware & Tools Connectors Y Branch Connectors FFFM & ;MMMF Connectors Rigid T splitters panel connectors Connector extensions Solar Wire crimper Solar wire connector wrenches $6.75 FREE SHIPPING Welding & Battery cableUSA Made 6 gauge to 4/0 Cable Battery cable links for inverters 6 AWG to 4/0, Various Hole Sizes Shrink Tubing Glue-Lined Marine Duty Need another Gauge or Length? 10 AWG 12 AWG Electrician’s tools TH0001 HD Cable Cutter $31.49 Cuts up to 4/0 Forged blades 12″ Handles TH0002 HD Cable Cutter $36 Cuts up to 500 MCM Forged blades 18″ Handles TH0003 HD Cable Cutter $45 Cuts up to 750 MCM Forged blades 24″ Handles TH0004 Hydraulic Knockout Punch $99 1/2″ to 2 ” Punch Set 9 US Tons 5 Year Warranty TH0005 Hydraulic Cable Crimper $99 6 AWG to 600 MCM (CU) 11 Ton Crimping Force 12 Die Sets TH0006 Hydraulic Cable Crimper $79 12 to 00 (2/0) AWG (CU) 5 Ton Crimping Force 12 Die Sets TH0007 Hammer Indent Crimper $20 8 to 0000 (4/0) AWG (CU) Universal Indent Die 5 Year Warranty TH0012 Dieless Indent Crimper $55 8 to 0000 (4/0) AWG (CU) Universal Indent Die 5 Year Warranty TH0020 Dieless Indent Crimper $89 10 AWG – 400 MCM Universal Indent Die 5 Year Warranty TH0021 Sheet Metal Stud Punch $145 3 Die Sets 20 GA, 0.393″ (1mm) Mild Steel TH0034 2 Speed Hydraulic Crimper $399 6 AWG to 750 MCM 12 Ton Crimping Force 12 Die Sets TH0037 Hydraulic Knockout Punch $275 1/2″ to 4″ Punch Set 13 US Tons 5 Year Warranty TH0247 HD Cable Cutter $39 Cuts up to 3/0 12″ Handle TH0248 HD Cable Cutter $55 Cuts up to 50 MCM 18″ Handle TH0249 HD Cable Cutter $69 Cuts up to 750 MCM 24″ Handle Shipping Domestic Lower 48 States: FREE! Local Pickup Available: FREE!* International Canada & Mexico: $20 Other Destinations:** $25 Orders are usually processed and shipped within 24 to 48 hours of receipt of your payment. Please provide us with a physical shipping address (failing to do so may delay your order). We may ship an order by a different courier at our discretion. If you need to receive an order within a guaranteed time frame, please contact us for rush options and expedited shipping. Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. Furthermore, we will not mark merchandise values below value or mark items as “Gifts”. *Local Pick Up is available at our Fremont CA location, Monday through Friday 9:00 a.m. to 5:00 p.m. Please contact us ahead to ensure that your item is in stock at our location before pick-up. ** International Buyers, Please Note: If shipping for your country is not listed, contact us for details. Payment & Returns Payment TEMCo accepts the following payment methods: PayPal, Visa, MasterCard, AMEX, Discover. We charge 9.75% sales tax for all orders shipping within California. Tax exemption is available if we are provided with a valid California resale certificate. Returns TEMCo allows for the return of products for 1 year from the date of purchase. Even if it’s opened, broken, or used, we will still accept your return and pay shipping both ways. We will replace the item with an identical item or issue a refund for the value of the item. Customer feedback We strive to provide 5-star service. Shop with confidence! 100% Positive reviews We want nothing more for our buyers than to be 100% happy with their purchase. We strive to earn a 5-star rating from every purchase. When you receive your purchase, please take a moment to leave us a positive feedback. If there was something unsatisfactory about your purchase, please contact us before leaving feedback and we’ll do what’s necessary to remedy the problem and ensure your satisfaction! When your order ships from our warehouse, we will automatically leave you positive feedback. “I have always been delighted with the service from TEMCo.” Your customer service, which is seldom needed, is wonderful, the staff knowledgeable and courteous. The shipping has been quite fast, which make my life easier… So, thank you, for the good experiences with the company! Rick C “I have ordered from TEMCo several times over the last 2 years and have always found the process to be simple and quick.” Making the order takes only a few moments, the product is always high quality and the shipping fast. Glen B “Thank you for a very satisfying and honest transaction.” It is really great to deal with a company that does exactly what they advertise. I can truly say I would recommend your company to anyone interested in the equipment you sell. Paul Gilley “The service was awesome.” I had many tech questions, and they spent about 30 mins on the phone answering all of them for me. It is not to often to find service like that!!!!! I am so happy and will definitly purchase from them again. A+++++ MRZ Contracting Still not sure about us? Check us out on the Better Business Bureau and Reseller Ratings, or look at our eBay seller ratings with a perfect score in all categories. View our other products Battery Link Cables Motor Capacitors Electric Motors Lighting magnet wire motor starters Phase converters raw material resistance wire ring terminals SO Cord Solar Tools & Hardware switches & Relays tools valves drives welding cable Shrink tubing About TEMCo Since 1968, TEMCo has become a trusted name in industrial power products. TEMCo products meet the demands of tough industrial applications with dependability and quality. We are proud to be an accredited member of the Better Business Bureau Online Reliability Program. Some of our customers include: TEMCo Industrial Sales, Manufacturing & Distribution 48621 Warm Springs Blvd Fremont, CA 94539 Contact us Send us a Message

10 Gauge Marine Wire,10 AWG 30Ft Duplex Marine Grade Wire Tinned Copper Oxygen-F

10 Gauge Marine Wire,10 AWG 30Ft Duplex Marine Grade Wire Tinned Copper Oxygen-Free Insulated Red& Black Electrical Cable for Boat/Automotive/Rv/Camper/Trailer. The marine grade duplex tinned copper wire is designed with a thick protective outer insulation coating makes it perfect for heavy-duty marine and other harsh external outdoor wiring projects.

Anderson SB175 Copper Battery Cable 2 Gauge AWG with ends lug/terminal/clamp

2 AWG GAUGE CUSTOM MADE BATTERY CABLE ASSEMBLY WITH ANDERSON SB175 PLUG TO YOUR CHOICE OF CONNECTORS ON OTHER ENDYOU CHOOSE THE LENGTH OF THE WIRE WITH AN SB175 INSTALLED ON ONE END AND CHOICE OF ONE OF THE 4 FOLLOWING OPTIONS FOR THE OTHER END:NO ENDS ON THE OTHER SIDECORROSION RESISTANT TIN PLATED PURE COPPER LUGSPURE COPPER TOP POST TERMINALS CORROSION RESISTANT TIN PLATED600 AMP EXTRA HEAVY DUTY PARROT JAW JUMPER CABLE CLAMPS These Anderson original SB175 plugs are ideal for use in quick plug instances such as booster cables, winches, and other battery cable connections. We start with the SB175 plug for 2 Gauge AWG wire and then crimp and assemble the plug with the length of wire you choose. We also give you the choice for a connector on the other end including corrosion resistant tin plated copper ring terminal lugs, top post battery terminal or jumper cable clamps. The options you choose allow you to construct the ideal cable to suit your needs. For example: If you wanted to make a quick connect jumper cable set you could choose a 3 foot cable with lugs to fit your battery and get a second cable assembly 12 foot long with jumper cable clamps. Another popular example is a mating set of cables so you could order 2 cable assemblies, each 3 foot long with lugs. Based off the design pioneered by Anderson in 1953, APP®s two pole SB® connectors set the standard for DC power distribution and battery connections. SB®175 connectors feature a one piece plastic housing using stainless steel springs to hold low resistance contacts in place. There is no “gender” to the plugs, no “male” or “female”…the plugs mate upside down with each other which aligns the Positive + and Negative- poles of the connector. The SB175 plug will mate with other SB175 plugs of the SAME COLOR! You cannot mate a RED and GRAY plug as they are made differently to avoid this. Also, the SB175 will not mate with a larger or smaller plug style such as the SB50 or SB350. The plugs will only mate with their own series (SB175). Two SB175 plugs of the same color will mate even with different wire sizes as the actual contacts are the same physical size meaning you can mate a GRAY SB175 with 4 AWG wires and a GRAY SB175 with 1/0 AWG wires with no problem. This again is a reason why this plug style is so popular in many battery applications. The plug is rated to handle up to 280 Amps (per UL 1977 Wire to Wire 1/0 AWG Max) and is listed to handle 175A of live current plugging and unplugging while under charge (UL Hot Plug Current Rating). The SB175 is rated up to 600V DC or AC. We carry additional SB175 plugs in our store if you need extra plugs for existing cables. If you need something special with regard to the length or lugs outside the available options please send us a message and we may be able to help you out. Also you can add notes to us during checkout with special configuration requests (although we prefer you message us first to discuss). ABOUT THE WIRE USED: This 2 AWG Gauge extreme battery cable is specially designed to meet the demands of various environments while staying extremely flexible. Full AWG sized copper conductor made from 99.9% pure annealed electrolytic copper, will you get maximum power. The insulation and jacket compounds are specially formulated to stay flexible even in cold weather and carry a -49C to 105C temperature rating. The jacket is resistant to chemicals, water, abrasions, oil, sunlight and has a color coded dual extrusion jacket with a white inner insulation which would show any damage to the outer cable more clearly. This cable is rated up to 600 Volts and is suitable for use in automotive applications, solar battery bank wiring, power inverter battery cables, marine battery cables and many other applications calling for a durable yet flexible battery cable. The battery cables meet the requirements of SAE J1127 and J378 making them ABYC and US Coast Guard approved for boat and marine use. BENEFITS OVER WELDING CABLE:Full AWG Size Copper ConductorTPE Jacket is Oil Resistant where EPDM on many welding cables is a poor insulator against oilSAE Rated for Automotive and Marine Uses BENEFITS OVER CCA POWER WIRE:Our cable is Copper…REAL COPPER but watch out for other “CCA Cable” as CCA Means Copper Clad Aluminum so you’d be using Aluminum which is a poor conductor compared to this pure copper cable! You have to use larger sizes of aluminum CCA cable, approximately 2 sizes larger to get close to the same power delivery as real copper cable! If you care about maximum power use our cable! The jacket on the cable reads as follows: BATTERYCABLESUSA.COM 2 AWG MARINE SAE J378/J1127 600V (-49C to 105C) MADE IN USA Benefits:ABYC and USCG Approved for use on boatsSAE J1127 ApprovedSAE J378 ApprovedTPE Jacket is Very Resistant to Oil, Water, Acid, Gas, Tears and AbrasionsThe Jacket Insulation Meets UL FT1 Flame Resistance RatingAnnealed Electrolytic Copper with Class K (Type III) Rope Lay for flexibilityFULL AWG Copper ContentMADE IN THE USA Specifications:Conductor Size: 2 AWG Stranding: 665 strands of copper (30 AWG ea strand, rope lay Class K)Outside Diameter of stranding: 0.320 inches (nominal)Outside Diameter of finished cable: 0.510 inches (nominal)Amps: Rated to handle 210 amps continuous outside of engine space (178 amps continuous inside engine space)Weight: 0.302 lbs per footSuitable Uses:Automotive Battery CablesMarine / Boat Battery CablesSolar Battery Bank ArrayForklift Charging CablesPower Inverter CablesWelding Cable LeadsAmplifier Wiring…and many other usesFinal pointers on lug sizing….most threaded stud batteries will have either a 5/16 or 3/8 inch stud. Most of the time the negative will be 5/16 so if the positive is the same size it is also 5/16, but if your battery stud is larger on the positive it will most likely be a 3/8. There are exceptions to the rule so please contact the manufacturer or measure. You can search online for bolt sizing tables which will help. If you have questions about cable sizing and whether this is the correct size feel free to send us a message and we will do our best to answer you or at a minimum steer you in the right direction. Also let us know if you need a different configuration than what is offered and we will tell you how to place the order with notes so we can build EXACTLY WHAT YOU NEED.

10 AWG Solar Panel Wire Per Foot Power Cable UL 4703 Copper USA Red PV Gauge

Visit Our Store Solar Wire Length: Sold by the foot. Just enter the number of feet you want into the quantity box when placing your order. Color: Red Conductor size: 10 AWG Feet per pound: 17.54 Nominal outside diameter (in.): 0.230 Conductor stranding: 19 strands per conductor Conductor material: Bare copper Insulation material: Cross linked Polyethylene (XLPE) Max. amps per conductor: 40 A Max. voltage: 600 V Min. temperature rating: – 40°C Max. temperature rating: 90°C Approvals: Type USE-2 per UL 854, RHH/RHW-2 per UL 44, Type PV per UL 4703 Applications: Solar panels, DC circuits, inverter wiring data sheet Download the full specs. UL 4703 Cable vs. Other Types of Cable What makes UL 4703 a better choice than some other common cable ratings, such as THHN or USE-2? Overview The term “PV wire” (photovoltaic wire) is often used to refer to USE-2 or THHN wire, the terms are not interchangeable. PV wire is specifically rated in accordance with UL 4703. THHN wire is used as general building wire and lacks the construction and strength of specialized cables designated as UL 4703 or USE-2. Using THHN cable in place of either UL 4703 or USE-2 will result in failures. Though USE-2 wire is impact and crush resistant, UL 4703 rated cable is superior to USE-2 in regards to low temperature flexibility, sunlight resistance, and flame resistance. PV wire for solar panels also has a thicker jacket and insulation than USE-2 wire. USE-2 cable is used in grounded PV systems only, which UL 4703 cable can be used for both grounded and ungrounded arrays. View the quick comparison chart below for an overview. Applications Per the National Electrical Code, USE-2 wire is suitable for use in grounded PV arrays only. UL 4703 cable can be used within both grounded and ungrounded PV arrays. THHN cable is used as general building wire and cannot replace USE-2 or UL 4703 cable. Temperature Rating PV cable is rated for 90°C in wet conditions and up to 150°C in dry conditions. USE-2 is rated for 90°C in both wet and dry conditions. THHN cable is rated at 75°C in wet conditions and 90°C in dry conditions. Voltage PV wire can be rated for 600 V, 1000 V, or 2000 V. THHN and USE-2 wire are only rated for 600 V. Flexibility PV wire is made up of stranded copper conductors, which makes it flexible. USE-2 wire is usually installed in locations where it is not subject to movement or mechanical damage, so they can use either solid or stranded conductors made of copper, copper-clad aluminum, or aluminum, making it less flexible than PV wire. Insulation and Jacket Both PV and USE-2 cable use thermoset insulation and jacket, typically XLPE (cross-linked polyethylene) or EPCV. Testing Requirements USE-2 cable is usually installed underground where it will likely not encounter flames, while PV wire can be exposed in an installation, so flames tests are required only for PV wire. Overload and mechanical abuse tests (including crushing and impact resistance) are applicable only to USE-2 cable. PV wire must pass more stringent testing requirements for sunlight resistance and low temperature flexibility. It undergoes a 720 hour weatherometer and a -40ºC cold chamber conditioning. In contrast, the requirements for USE-2 cable are 300-hour weatherometer and -25ºC cold chamber conditioning. UL 4703 (PV Wire) Applications: Wiring solar panels. Underground service entrance wire for both grounded and ungrounded PV arrays.General purpose wiring for installation in conduit. Min. conductor size: 18 AWG Insulation: Cross-linked Polyethylene (XLPE) Jacket: May or may not have jacke Temp rating: 90°C Wet, 150°C Dry Max Voltage: 600, 1000, or 2000 V Resistant to: Sunlight, ozone, UV, flame, moisture Flexibility at low temperatures: Higher Standards: Type USE-2 per UL 854 RHH/RHW-2 per UL 44 Type PV per UL 4703 THHN (Building Wire) Applications: General purpose wiring for installation in conduit. May also be used in machine tool, appliance and control circuit wiring. Cannot replace PV or USE-2 if standards require it. Min. conductor size: 14 AWG Insulation: Polyvinylchloride (PVC) Jacket: Nylon Temp rating: 75°C Oil, 75°C Wet, 90° Dry Max Voltage: 600 V Resistant to: Gasoline and oil Flexibility at low temperatures: Lower Standards: UL 83 & 1063 as Type THHN Wire 90°C in dry locations. Type THWN Wire 75°C in wet locations. A-A-59544, NEMA WC-5, UL-758 USE-2 (RHH/RHW Wire) Applications: Aerial, raceway, or direct burial. For connecting PV modules. Grounded PV arrays only. Min. conductor size: 14 AWG Insulation: Cross-linked Polyethylene (XLPE) Jacket: May or may not have jacket Temp rating: 90°C Wet and Dry Max Voltage: 600 V Resistant to: Crushing and impact, sunlight Flexibility at low temperatures: Lower Standards: UL 44 for rubber covered wire. UL 854 for service entrance cable. Federal Govt. Specificiation J-C-30A, ASTM-B-3 (solid copper conductors), ASTM-B-3 and 6 (standard conductors) Features Resistant to sunlight, ozone, UV, flame, and moisture. Proudly Made in the U.S.A. ZERO WIRE IMPORTS POLICY. We have a Physical Location. If you have questions, we want to hear from you. Wanna talk or pick up your order? Stop by! We’d be glad to have you. Best Price/Quality Guaranteed! We pass on our buying power with low prices. Excellent Quality Guaranteed! Give us a call or drop by, and we’ll show you. As an OEM, we use many of the products we sell. As a result, only high quality materials are offered to you. Get it FAST. Most orders received in 2 to 5 days. Our return policy. If you don’t like it, we’ll take it back and pay the shipping! Other Solar Hardware & Tools Connectors Y Branch Connectors FFFM & ;MMMF Connectors Rigid T splitters panel connectors Connector extensions Solar Wire crimper Solar wire connector wrenches $6.75 FREE SHIPPING Welding & Battery cableUSA Made 6 gauge to 4/0 Cable Battery cable links for inverters 6 AWG to 4/0, Various Hole Sizes Shrink Tubing Glue-Lined Marine Duty Electrician’s tools TH0001 HD Cable Cutter $31.49 Cuts up to 4/0 Forged blades 12″ Handles TH0002 HD Cable Cutter $36 Cuts up to 500 MCM Forged blades 12″ Handles TH0003 HD Cable Cutter $45 Cuts up to 750 MCM Forged blades 12″ Handles TH0004 Hydraulic Knockout Punch $99 1/2″ to 2 ” Punch Set 9 US Tons 5 Year Warranty TH0005 Hydraulic Cable Crimper $99 6 AWG to 600 MCM (CU) 11 Ton Crimping Force 12 Die Sets TH0006 Hydraulic Cable Crimper $79 12 to 00 (2/0) AWG (CU) 5 Ton Crimping Force 12 Die Sets TH0007 Hammer Indent Crimper $20 8 to 0000 (4/0) AWG (CU) Universal Indent Die 5 Year Warranty TH0012 Dieless Indent Crimper $55 8 to 0000 (4/0) AWG (CU) Universal Indent Die 5 Year Warranty TH0020 Dieless Indent Crimper $89 10 AWG – 400 MCM Universal Indent Die 5 Year Warranty TH0021 Sheet Metal Stud Punch $145 3 Die Sets 20 GA, 0.393″ (1mm) Mild Steel TH0034 2 Speed Hydraulic Crimper $399 6 AWG to 750 MCM 12 Ton Crimping Force 12 Die Sets TH0037 Hydraulic Knockout Punch $275 1/2″ to 4″ Punch Set 13 US Tons 5 Year Warranty Shipping Domestic Lower 48 States: $3.50 Local Pickup Available: FREE!* International Varies by location. Orders are usually processed and shipped within 24 to 48 hours of receipt of your payment. Please provide us with a physical shipping address (failing to do so may delay your order). We may ship an order by a different courier at our discretion. If you need to receive an order within a guaranteed time frame, please contact us for rush options and expedited shipping. Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. Furthermore, we will not mark merchandise values below value or mark items as “Gifts”. *Local Pick Up is available at our Fremont CA location, Monday through Friday 9:00 a.m. to 5:00 p.m. Please contact us ahead to ensure that your item is in stock at our location before pick-up. ** International Buyers, Please Note: If shipping for your country is not listed, contact us for details. Payment & Returns Payment TEMCo accepts the following payment methods: PayPal, Visa, MasterCard, AMEX, Discover. We charge 9.75% sales tax for all orders shipping within California. Tax exemption is available if we are provided with a valid California resale certificate. Returns TEMCo allows for the return of new and unused products in original factory condition and used defective products for 30 days from the date of purchase. Returns must be pre-approved by TEMCo and have a return merchandise authorization (RMA) number issued by TEMCo. Unauthorized returns will not be accepted. We recommend using a shipping carrier with online tracking and insurance. TEMCo will replace the item with an identical item, issue a full store credit for the value of the item, or issue a refund for the value of the item, minus a 20% restocking fee. Items with a 100% satisfaction guarantee are exempt from the 20% restocking fee. Customer feedback We strive to provide 5-star service. Shop with confidence! 100% Positive reviews We want nothing more for our buyers than to be 100% happy with their purchase. We strive to earn a 5-star rating from every purchase. When you receive your purchase, please take a moment to leave us a positive feedback. If there was something unsatisfactory about your purchase, please contact us before leaving feedback and we’ll do what’s necessary to remedy the problem and ensure your satisfaction! When your order ships from our warehouse, we will automatically leave you positive feedback. “I have always been delighted with the service from TEMCo.” Your customer service, which is seldom needed, is wonderful, the staff knowledgeable and courteous. The shipping has been quite fast, which make my life easier… So, thank you, for the good experiences with the company! Rick C “I have ordered from TEMCo several times over the last 2 years and have always found the process to be simple and quick.” Making the order takes only a few moments, the product is always high quality and the shipping fast. Glen B “Thank you for a very satisfying and honest transaction.” It is really great to deal with a company that does exactly what they advertise. I can truly say I would recommend your company to anyone interested in the equipment you sell. Paul Gilley “The service was awesome.” I had many tech questions, and they spent about 30 mins on the phone answering all of them for me. It is not to often to find service like that!!!!! I am so happy and will definitly purchase from them again. A+++++ MRZ Contracting Still not sure about us? Check us out on the Better Business Bureau and Reseller Ratings, or look at our eBay seller ratings with a perfect score in all categories. View our other products Battery Link Cables Motor Capacitors Electric Motors Lighting magnet wire motor starters Phase converters raw material resistance wire ring terminals SO Cord Solar Tools & Hardware switches & Relays tools valves drives welding cable About TEMCo Since 1968, TEMCo has become a trusted name in industrial power products. TEMCo products meet the demands of tough industrial applications with dependability and quality. We are proud to be an accredited member of the Better Business Bureau Online Reliability Program. Some of our customers include: TEMCo Industrial Sales, Manufacturing & Distribution 48621 Warm Springs Blvd Fremont, CA 94539 Contact us Send us a Message

10/2 AWG Gauge Marine Grade Wire, Boat Cable, Tinned Copper, Flat Red/Yellow

10 AWG 2 Conductor Wire, Marine Grade Boat Cable with White overall jacket with Red and Yellow conductors inside used for wiring DC applications. This wire is UL1426 listed and exceeds the requirements of ABYC and the USCG (US Coast Guard) for installation on boats. Very flexible and designed to withstand the harsh marine environment.Color Code: Red and Yellow Conductors (Safety DC Color Code with Red for Positive and Yellow for Negative)Copper stranding is tin plated to resist corrosion, Flexible Type III, Class K strandingMeets all applicable boat wiring regulations from ABYC and US Cost Guard for use on boatsRated 600 Volts Max with 105C Dry and 75C Wet (BC5-W2) temperature ratings and will remain flexible in extreme cold weatherJacket and insulation are resistant to oil, gas, salt water, battery acid, heat, abrasion and sunlightSpecifications for Flat Duplex Marine Wire:Wire Size (AWG) Dimensions Weight/FT Amps Max* 18/2 3/16″ x 9/32″ .049 lbs 20 16/2 3/16″ x 5/16″ .051 lbs 25 14/2 7/32″ x 11/32″ .065 lbs 35 12/2 7/32″ x 3/8″ .082 lbs 45 10/2 1/4″ x 15/32″ .128 lbs 60 8/2 11/32″ x 5/8″ .230 lbs 80 6/2 13/32″ x 3/4″ .364 lbs 120 *Inside of engine space de-rate amps by 15% due to extra heat Feel free to contact us with any questions you have prior to ordering and we will help you out to the best of our ability.