Garage Door Torsion Springs PAIR .218 x 2″ ID x Select Length – USA MADE*
This Listing is for One Pair of .218 X 2″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringsPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Pair of Springs (1 Right Wound, and 1 Left Wound)1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .218, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering. Step 1. is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size. Double check by measuring 20 coils and compare to the 20 coil measurement. If the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched (no gaps between the wires). Do not take your measurements on the ends where the wire goes over the cones are. The cones tend to stretch the wire apart causing gaps between the wires. Any gaps between the wires will not give an accurate measurement. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter (ID). If the spring is broken you can simply use a ruler to measure the inside of the broken end. If the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID; for instance P200 or P2000 will be stamped on the cones for a 2” ID and P175 for a 1 3/4″ ID. The most common sizes in residential springs are 1 3/4″ and 2″ (Raynor doors use a 2 ¼” ID). Step 3 is to measure the length of the spring. Measure the spring only; do not include the winding and stationary cones. If the spring is broken, measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and still wound, it will be longer by 2-3” than when it is relaxed. The proper way to measure for the length is to unwind the spring and then measure. Step 4 is only important if ordering a single spring. You will need to determine the wind direction of the spring (right hand wind {RW}) or left hand wind {LW}). Look at the third photo on this listing for an example of the two different spring wind directions. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Track For 7′ High Door – Pair of Vertical Sections 76″ in Length
One Set of New Heavy Duty Garage Door Vertical Track for 7′ High DoorFrom drop down box Choose Standard length (76″) or custom length. Custom length is anything less than 76″. NOTE: IF CUSTOM LENGTH is Selected, PLEASE LEAVE A MESSAGE WITH YOUR ORDER STATING THE LENGTH THAT YOU NEED THE TRACK CUT DOWN TO.Brand New, Never UsedThese are Quality, Heavy Duty Track .05 ThicknessFits most doors using 2” trackIncludes 2 each #4 Jamb Brackets, 2 each #5 Jamb Brackets, and Fasteners. Vertical track piece is 76” in length. Note: Shipping charges are high due to the size of item. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purcha RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Track Piece 1′, 2′, 3′ 4′, 5′ lengths! random cuts of vertical track
This listing is for pieces of 2″ garage door track. The lengths offered are 12″, 24″, 36″, 48″, and 60″. Track pieces only; NO jamb brackets and NO fasteners included. TO NOTE: pieces are randomly cut; there is no guarantee of where the hole placement(s) will be on the piece of track. The photos are for reference only. The hole placements on the pieces you receive will most likely be different than what is pictured. Some pieces may not have any holes at all. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purcha RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingAll items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Torsion Springs PAIR .250 x 2″ ID x Select Length -USA MADE*
This Listing is for One Pair of .250 X 2″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringsPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Pair of Springs (1 Right Wound, and 1 Left Wound)1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .250, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering. Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Linear Garage Door Opener Key Chain Remote Control Part For LD033 LS050 LC075
Linear Garage Door Opener Key Chain Remote Control Part For LD033 LS050 LC075 1 Key Chain Remote . 2 Channel remote .
SET OF 10 Zebra Animal Print Ceramic Cabinet Drawer Knobs – CLEARANCE
THIS IS A CLEARANCE ITEM. ONCE THEY ARE GONE WE WILL NOT RESTOCK New 1 1/2 inch CERAMIC knobS – Set of 10. Price is for 10 knobs. One inch mounting screw included.Design covers the entire knob – not just the top.In stock and ready to ship.Great addition and nice finishing touch to any room! SHIPPING INFO:Clearance items are NOT eligible for promotional shipping discounts. PAYMENT INFO:We accept Paypal only.Credit card payments are accepted/processed through Paypal.NC residents are subject to sales tax. CUSTOM ORDERS:We accept custom orders, and can make most any design you are interested in.Custom orders are listed as buy it now and the item number will be e-mailed to you. Carolina Hardware and Decor is not affiliated with any other company.
Zebra ANIMAL Print CABINET White Ceramic DRAWER Pull KNOB
New 1 1/2 inch CERAMIC knob. Price is for one knob. One inch mounting screw included. Great addition and nice finishing touch to any room!! SHIPPING INFO: For shipping times and combined shipping information, please read our Shipping Policy. PAYMENT INFO: Payment due within 7 days of end of auction. We accept Paypal only. Credit card payments are accepted/processed through Paypal. NC residents are subject to sales tax. CUSTOM ORDERS: We accept custom orders, and can make most any design you are interested in. Custom orders are listed as buy it now and the item number will be e-mailed to you. Carolina Hardware and Decor is not affiliated with any other company.
Glow Boy 5/8″ Door Rope Gasket White + Cement KS-5060-1160 AGDRGA60
Glow Boy KS-5060-1160 AGDRGA60 Door Rope Gasket – 5/8″ x 5′ PLUS 1 tube Gasket cementPellet / Wood Stoves:Replacement Fits the following models:FPPBW2GD BayviewFPPBW2GD-RF BayviewFPPST4BD Step TopFPPST4BD-RF Step TopHCPP2BD-RF Home Heater 120HHPP2BD-RF Home Heater 120HHPP2BDD-M Home Heater 120HHPP2BDD-RF Home Heater 120HHPP32BD Home Heater 300HHPP32BD-RF Home Heater 300IPPBW-LRG Bayview InsertIPPBW-LRG-LOG Bayview InsertIPPBW-SML Bayview InsertIPPBW-SML-LOG Bayview Pellet InsertIPPBW2GD Bayview InsertIPPBW2GD-LS Bayview InsertIPPBW2GD-RF Bayview InsertIPPBW2GD-SS Bayview InsertPP300 MAXIMUM OPERATING TEMPERATURE 1,000°F (538°C) max.FEATURES High temperature applicationsIdeal door sealLow compression, helps form around irregular surfacesHigh flexibilityUse over irregular surfacesThermal protectionHigh tensile strengthNon-flammableVersatileMade in USA); if(document.body != null){ document.body.appendChild(sctTag1); } . look in our store for more Vermont Castings Gasket Kits -We ship secure with tracking! Item will generally ship out between 24-48 hours on business days (or earlier).Payment:-Must be made through PayPal no later than 24 hours after your Pay, If you do not make your payment within 24 hours then we reserve the right to cancel relist the Item. Return policy:-14 day return policy. Item must be in the same condition as we shipped it out in. Please note That I personally inspect every item before it ships out..-Buyer is responsible for return shipping.-A 20% restocking fee will apply unless the item is defective. In such cases we will exchange the item at no cost to you and if a exchange is N/A we will give a full refund up to 14 Days after you receive the item.Feedback:-We will leave Positive feedback only after we receive positive feedback from you. If for any reason you are unhappy please do not run and open up a case without first contacting us and giving 24-48 hours to get back to you so we can resolve any issue you might have within reason. Although we try are very best to do everything perfect please remember everyone makes mistakes once in a while and in the slim chance that I do I will absolutely try my best to fix it. Thank You!!! FOR INTERNATIONAL ,,,,,,,,,ONLY EBAY GLOBAL INTERNATIONAL SHIPPING. !!!!!!!!! Pennsylvania Residents You must pay sales tax on this item unless a valid PA SalesTax Exempt Number and a signed and complete Tax Exemption Certificate is provided. Get a copy at, http://www.revenue.state.pa.us/revenue/lib/revenue/rev-1220.pdf If the link doesn’t work just copy and paste in a new window to find the form. Track Page Views With Auctiva’s FREE Counter
Moroccan Kitchen Tiles Ceramic Mexican Spanish Mediterranean Zellige Mosaic Art
These Moroccan tiles are made from red clay , they are meant to be used for the outside and inside, they resist all kind of weather conditions and temperatures. Moroccan tile or zellige is ideal for the bathroom and kitchen due to there durability and resistance to the dampness. They will Decorate your wall with a unique style and taste or be a perfect gift. Tiles can be easily wall mounted on any surface with mortar or tile adhesive. Measurement : 4 inches length by 4 inches wide by 3/4 depth ***Free Shipping *** Add a map to your own listings. FREE Trial!
100 FT. 100′ Feet CLEAR 1/4″ 6mm Polyolefin 2:1 Heat Shrink Tubing Tube Cable US
1/4″ (ID) x 100 feet Length Spool 2:1 Ratio Polyolefin Clear Heat Shrink TubingCLICK HERE for Heat Shrink in Different Sizes, Colors, & LengthsHigh Quality Flexible Polyolefin Features & Specifications: Color: Clear Inner Diameter(ID): 1/4″ Length: 100 Feet Shrink Ratio: 2:1 (Shrinks to 1/2 of its original diameter) Highly Flame Retardant UL224 125° C UL Listed & CSA Certified RoHS Compliance Operating Temperature: -55° C to +135° C (-67° To 275° F) Maximum Continuous use Temperature: 135° C (275° F) Voltage Rating: 600V Applications: Electrical Insulation, Strain Relief, Cable Bonding, Color-Coding, Wire Marking, Corrosion Protection, Solder Insulation, Wire Bunding & more.