2Pack Mighty Mule GTO Rev Counter Board for Automatic Gates- RVCTBD50
Rev Counter Board Replace for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Product Description Rev Counter Board: Calculate the opening distance of the opener and solve the problem that your door cannot be opened correctly,Consists of a tachometer and a limit switch to prevent your gate arm from running off Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Replacement for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Please sealing and draining during installation,avoid short circuit of the circuit board caused by water ingress and failure to work properly. mounting type: Door Mount Installation Steps: 1.First, you must turn off the power switch on the lower left side of the control boxThe control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly 2.Remove the cotter pins at the ends of the gate arms Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor Then use the T20 tool head to remove the 14 screws Less than 2 minutes with a battery operated tool 3.You open the clamshell housing an inch or so and unplug the pin connector cable Note that the cover does not come off, but rotates open 4.A shorter T20 screw holds the board to the assembly, screw the board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board 5.After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out 6.Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on The control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly The product does not have a manual
2Pack Mighty Mule GTO Rev Counter Board for Automatic Gates- RVCTBD50
Home Payment Shipping About us Contact us Store Categories Store Categories Electronics Fashion Motors Home&Garden Others Product View Details Composition: Consists of a tachometer and a limit switch to prevent your gate arm from running off Suitable for: FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Mighty Mule,GTO PRO 2500 series Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Waterproof coating: surface gel coating to refuse the erosion of moisture, enhance the practical cycle, do not have to worry about the impact of fog, rain, snow or heat and humidity, so you can easily drive into the home Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Product Details Item Weight: 0.81 ounces Package Dimensions: 3.7 x 3.1 x 1.1 inches Item Package Quantity: 1 Batteries Included?: No Batteries Required?: No We strive to provide easy-to-understand content to eliminate confusion when purchasing products We cut through the version confusion to help you find the right replacement part for your needs We take the extra step to make sure you get the right product for your project The parts we sell are designed for all specific generations of gate openers Installation Steps: 1 First, you must turn off the power switch on the lower left side of the control box. 2Remove the cotter pins at the ends of the gate arms. Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor. Then use the T20 tool head to remove the 14 screws. Less than 2 minutes with a battery operated tool. 3 You open the clamshell housing an inch or so and unplug the pin connector cable. Note that the cover does not come off, but rotates open. 4 A shorter T20 screw holds the board to the assembly, screw the new board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board. 5 After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out. 6 Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on. Note: There is no manual Payment Method Shipping Policy Returns Policy About us Contact us Payment Method Shipping Policy Returns Policy [RETURN_POLICE] About us Contact us Home Payment Shipping About us Contact us
Mighty Mule RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Rev Counter Board Replace for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Product Description Rev Counter Board: Calculate the opening distance of the opener and solve the problem that your door cannot be opened correctly,Consists of a tachometer and a limit switch to prevent your gate arm from running off Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Replacement for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Please sealing and draining during installation,avoid short circuit of the circuit board caused by water ingress and failure to work properly. mounting type: Door Mount Installation Steps: 1.First, you must turn off the power switch on the lower left side of the control boxThe control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly 2.Remove the cotter pins at the ends of the gate arms Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor Then use the T20 tool head to remove the 14 screws Less than 2 minutes with a battery operated tool 3.You open the clamshell housing an inch or so and unplug the pin connector cable Note that the cover does not come off, but rotates open 4.A shorter T20 screw holds the board to the assembly, screw the board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board 5.After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out 6.Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on The control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly The product does not have a manual
For RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Mighty Mule RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Rev Counter Board Replace for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Product Description Rev Counter Board: Calculate the opening distance of the opener and solve the problem that your door cannot be opened correctly,Consists of a tachometer and a limit switch to prevent your gate arm from running off Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Replacement for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Please sealing and draining during installation,avoid short circuit of the circuit board caused by water ingress and failure to work properly. mounting type: Door Mount Installation Steps: 1.First, you must turn off the power switch on the lower left side of the control boxThe control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly 2.Remove the cotter pins at the ends of the gate arms Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor Then use the T20 tool head to remove the 14 screws Less than 2 minutes with a battery operated tool 3.You open the clamshell housing an inch or so and unplug the pin connector cable Note that the cover does not come off, but rotates open 4.A shorter T20 screw holds the board to the assembly, screw the board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board 5.After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out 6.Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on The control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly The product does not have a manual
For RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Mighty Mule RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Rev Counter Board Replace for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Product Description Rev Counter Board: Calculate the opening distance of the opener and solve the problem that your door cannot be opened correctly,Consists of a tachometer and a limit switch to prevent your gate arm from running off Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Replacement for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Please sealing and draining during installation,avoid short circuit of the circuit board caused by water ingress and failure to work properly. mounting type: Door Mount Installation Steps: 1.First, you must turn off the power switch on the lower left side of the control boxThe control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly 2.Remove the cotter pins at the ends of the gate arms Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor Then use the T20 tool head to remove the 14 screws Less than 2 minutes with a battery operated tool 3.You open the clamshell housing an inch or so and unplug the pin connector cable Note that the cover does not come off, but rotates open 4.A shorter T20 screw holds the board to the assembly, screw the board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board 5.After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out 6.Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on The control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly The product does not have a manual
Mighty Mule RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Product Description GTO RVCTBD50 Rev Counter Board Mighty Mule 350, Mighty Mule 500, Mighty Mule 502, GTO PRO 2500 series Product Features and Specifications GTO Rev Counter Board Fits: Mighty Mult 350, Mighty Mule 500, Mighty Mule 502, GTO PRO 2500 series Manufacturer: GTO / Mighty Mule Part Number: B00WXQ4352 Item Weight: 0.81 ounces Package Dimensions: 3.7 x 3.1 x 1.1 inches Item model number: B00WXQ4352 Is Discontinued By Manufacturer: No Item Package Quantity: 1 Batteries Included?: No Batteries Required?: No Date First Available: June 8, 2015
For RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Mighty Mule RVCTBD50 Rev Counter Board Gate Operator Control Board FM350 MM350
Rev Counter Board Replace for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Product Description Rev Counter Board: Calculate the opening distance of the opener and solve the problem that your door cannot be opened correctly,Consists of a tachometer and a limit switch to prevent your gate arm from running off Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time Replacement for FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series Replacement for Mighty Mule GTO Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money Please sealing and draining during installation,avoid short circuit of the circuit board caused by water ingress and failure to work properly. mounting type: Door Mount Installation Steps: 1.First, you must turn off the power switch on the lower left side of the control boxThe control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly 2.Remove the cotter pins at the ends of the gate arms Leaving all the wiring in place, you turn the gate arm upside down and place it on a piece of cardboard on the floor Then use the T20 tool head to remove the 14 screws Less than 2 minutes with a battery operated tool 3.You open the clamshell housing an inch or so and unplug the pin connector cable Note that the cover does not come off, but rotates open 4.A shorter T20 screw holds the board to the assembly, screw the board on, and then reinsert the connector, Make sure the orange and green cables match the markings on the board 5.After getting all this accumulated junk out, it’s a good idea to put some wire or small nails in the drainage holes on the bottom, to make sure the water can drain out 6.Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on The control lever on the switch is lengthened, which can be installed with confidence, avoiding the trouble of repeated disassembly The product does not have a manual