Diablo DSP-55 Plug-in Vehicle Loop Detector 10 Pin for All-O-Matic Elite Linear
Diablo DSP-55 Plug-in Vehicle Loop Detector 10 Pin for All-O-Matic Elite Linear Plug-in loop detector for the following operators All-O-MaticElite AccessLinear ProMaximum ControlsViking AccessAdjustable frequency and Sensitivity Features Can be connected to a standard inductive loop as well as Diablo Controls mini-loops.Small profile, perfect for many installations.Three Solid State outputs.Fail-safe or Fail-secure operation.Wide low-voltage operation Separate Power/Fail and Detect LEDs.B Outputs can be presence, pulse on entry, pulse on exit, or loop fail.Flicker display shows occupancy of the detection zone when operating in a pulse mode.Delay or extension time is possible.
Diablo Controls DSP- 55 Plug-in Vehicle Loop Detector
Diablo Controls DSP- 55 Plug-in Vehicle Loop Detector Diablo Controls DSP- 55 Plug-in Vehicle Loop Detector The DSP-55 detector is intended to be a full-featured single channel detector that can work with both inductive loops as well as the new Diablo Controls mini-loops. Many features have been included which are normally found only on more expensive models. The small package is powered by a high-performance 8-bit microcontroller that does not skimp on performance. The DSP-55 detector has a small footprint and was designed to retrofit into many existing locations that may require a detector upgrade. This allows maintenance personnel to carry only one detector to meet most, if not all, of their vehicle detection needs.The detector uses a 10-pin Molex connector for its connections and has three solid-state (open-collector) outputs. The solid-state outputs allow for a smaller total package size, lower power consumption, and elimination of contact bounce.FeaturesCan be connected to a standard inductive loop as well as Diablo Controls mini-loops.Small profile, perfect for many installations.Three Solid State outputs.Fail-safe or Fail-secure operation.Wide low-voltage operation Separate Power/Fail and Detect LEDs.B Outputs can be presence, pulse on entry, pulse on exit, or loop fail.Flicker display shows occupancy of the detection zone when operating in a pulse mode.Delay or extension time is possible. Payments & Returns Policy
Diablo DML-9LP Low Voltage Solar Power Free Exit Probe Vehicle Detector
Diablo DML-9LP Low Voltage Solar Power Free Exit Probe Vehicle Detector LED Indicators: The green Power LED blinks once per second to indicate the detector is operating and powered. The red Detect LED will turn on when a vehicle is over the loop detection area. Loop or Wire Failures: In the case of a loop circuit failure, the green LED flashes slowly (twice per second) for an open loop circuit failure. The green LED will flash fast (10 times per second) to indicate a shorted loop circuit. Pulse Operation: This detector only outputs a single 125 ms pulse when the vehicle passes over the detection area. There is no option to operate in the presence mode. Fail Safe vs Fail Secure: A fail safe detector will output “detect” when the loop circuit is failed. On the free exit loop this will keep the gate open until the situation is fixed. This is useful in applications where it is important to allow traffic flow to continue. A fail secure detector will never output “detect” when the loop circuit is failed. This will keep the gate closed. This is useful in high-security areas or installations where containment is needed. The DML-9LP is a fail secure detector. Note: Never use a fail secure detector on a safety loop. Power: This detector is powered with 10 to 30 volts AC or DC. Approximately 1 mA current. The relay contacts are rated at 1 amp maximum. Size: Height: 1.52″ Width: 2.9″ Depth: 1.56″ Operating Temperature: -35°F to 165°F (-37°C to 74°C) Features Designed for solar powered applicationsPlug and playSmall profile, making it perfect for many installationsDesigned to be cross talk free between other loopsAutomatically compensates for loop and lead-in sizesSwitch-less, self-adapting to most common installationsFail secure operationWide low-voltage operationConnector: Removable 7-pin terminal block. Pin assignments are shown below (from left to right): 1. Relay Normally Closed (NC) – contact opens for detect 2. Relay Common 3. Relay Normally Open (NO) – contact closes for detect 4. Power Common 5. Power In (10 to 30 volts AC or +DC) 6. Mini-Loop 7. Mini-Loop