Ultra Custom Pools

Item Tag: IT-KIT-2

2 pack – Granite & Marble Acrylic Repair Diy Kit – Light Cure

Hi Folks, This is a listing for 2 kits. Enables you to make fast and permanent repairs (defects like chips, nicks, pits, deep scratches and surface defects) on Natural and engineered stones like Granite, Marble, Travertine, Limestone, Slate, Sandstone, Quartzite. Advanced Light Cure Technology. Can be used safely on Food Preparation surfaces. Non-toxic material. It cures with visible blue light in minutes and all repair process takes less than 10 minutes. The kit has enough material and accessorries to make 3 average size repairs. Box Dimensions = 170 mm (Length) x 100 mm (Width) x 20 mm (Height) Overall weight is 50 Grams. Better price, better quality 2 Kits include 1.0 grs of Light Cure Clear Flowable Material x 2 1 Microtip x 2 1 x 10 cm Leveling Tape x 21 pcs of Blue Light Key Chain x 2 2 pcs of Sandpaper (220 grid x 1, 2000 grid x 1) x 20,5 gr of Polisher Paste x 2Stick x 2 “UPS REQUIRES A PHONE NUMBER FOR INTERNATIONAL SHIPMENTS. PLEASE PROVIDE YOUR PHONE NUMBER DURING CHECK OUT”

Leather Accessory Kit By Make Market – Do It Yourself NEW

The Leather Accessory Kit by Make Market is a DIY kit that allows you to make 2 projects using various materials. Whether you’re a beginner or a skilled crafter, this kit provides everything you need to create your own personalized leather accessories.

Steel-It Epoxy Finish 4907A 4907B (2 Gallon Kit)

STEEL-IT Epoxy Finish 4907G (2 Gallon Kit) STEEL-IT is a truly revolutionary product. The STEEL-IT line of coatings contain stainless steel pigment, for a long-lasting rust proof coating. This is the Epoxy Finish. It comes in a 2 Gallon Kit – you mix them together. So, yes, you will wind up with 2 gallons of Epoxy Finish for each of these kits purchased. Coverage: 400 sq ft/per kit @ 3 mils thick. Protects Steel from: Impact and abrasion Mild and strong alkalies Solvents and chemical spillage Moisture (fresh and salt) 2 coats – STEEL IT Epoxy Coating #4907 Surface Preparation: General use – Sandblast to an SSPC-SP-6 (commercial) or an SSPC-SP-10 (near white) blast quality. Immersion or Chemical Exposure – Sandblast to an SSPC-SP-5 (white) blast quality. Anchor Pattern cut and angular 1.5 – 2.5 mils deep. Film Thickness: Atmospheric Service and Light Chemical Exposure – 3 dry mils primer and 3 dry mils of finish. Immersion and heavy-duty chemical exposure – 3 dry mils of primer and 2 coats of finish (3 dry mils each). Mixing: Thoroughly agitate each part separately, then blend one to one by volume (Part A and Part B). Allow 30 – 45 minutes induction time. Re-agitate and strain through filter before use. Pot Life: 6 – 8 hours Application: For spray application use a DeVilbiss JGA and MBC gun with a 705FF Air-cap/Fluid Tip Combination. For airless application use a 28:1 pump (minimum) with a DeVilbiss JGB-501 Gun. Fluid Tip Orifice of .015 – .021 is recommended. May also be applied by brush or roller. Dry Time: Dry to touch in 2 hours. Allow 12 hours between coats. Subsequent coats will be tack free to handle in 24 hours. Light service in 36 hours. For complete cure (full production and hardness) allow 6-7 days. Coverage: Theoretical coverage, Epoxy Finish #4907: 200 sq. ft. per gallon at 3 mils DFT (dry film thickness).In practice, these values can be reduced by at 25% by loss factors. Thinning and Clean Up: Thin only if necessary, using STEEL IT #6811 Epoxy Reducer or small amounts of aromatic, glycol ether based solvents. Clean-Up with aromatic, glycol ether, ketones or mixtures of the same. Limitations: Apply only when surface and ambient temperatures are above 50°F. Relative humidity must be less than 86%. Surface temperature must be at least 5°F above the dew point. Recommended for surfaces where the operating temperatures will not exceed 200°F.