0-10V, 0-20V, 1-10V 2000W 220-240V AC Led dimmer switch made in Australia
Przed kupieniem prosze sie skontaktowac ze mna TECHNICAL PARAMETERS: SOFT START The Dim2000 dimmer incorporates a soft start feature providing a noticeably smooth lamp illumination at turn on. This feature also minimise lamp filament start up stress, which may increase lamp life. (It’s recommended by manufacture to start dimming from lower brightness to max). THERMAL OVERLOAD COMPPENSATION The lamp brightness is automatically reduced in the event of high ambient temperatures or overload of the dimmer for a long time. It resets automatically when conditions are corrected. THERMAL CUT-OUT x 2 Dim2000 includes two types of thermal fuses. The first is a non-resettable design that will burn out in the event of catastrophic circuit failure. The second is resettable and will automatically reduce the brightness to “0”, if the dimmer is accidentally overloaded or overheated, it resets automatically when the overload conditions are corrected or the dimmer has cooled down. SHORT CIRCUIT PROTECTION* The Dim2000 series dimmer feature short circuit protection, design to ensure the dimmer can survive in case of wiring fault or catastrophic failure of the load. To resume to normal operation the dimmer needs to be switch OFF (disconnected from mains) and turn ON to resume operation. FUSE CUT-OUT The unit contain fast type fuse designed to blow or open in case of catastrophic circuit failure. This is a secondary protection measure intended to operate as a backup in case of persistent or prolonged overload conditions. If the fuse blow (fuse open), need to be replaced. Any significant overload should be avoided in order to prevent damage to the Dimmer. DIM2000 AC Phase Cut Dimmer Controller Features § Ground Leakage Current for Flicker Reduction. § User Programmable Leading or Trailing Edge Dimming Control § Dynamic Over-Current and Temperature Protection § Powered from the AC Line § Symmetric AC Current Control § Gate Pulse Width Programmable from 0 to 100% tON § 8 Bit ADC Input for Dimming Control with an Adjustable Resistor or 0 to 10 V DC Voltage § 226 Dimming Pulse Widths with 25 ms Resolution and Built-in Ramp Up/Down Control for Smooth Dimming § Automatically reduces the output voltage in the event of an increase in mains voltage like power surge. § Military Components § 600 mA Quiescent Current § Precision Temperature Compensated 2% Internal Timer § Low Power Electronic Off State Mode § 50 Hz and 60 Hz Options § 0-10V DC Input with Optical Isolation Option Applications § Dimmer Switches § Light’s control § AC Controls § Heaters control system § Safety Switch (On/Off) Number of outputs 1 Nominal Mains Supply Voltage 220 – 240V AC AC voltage range 190-264V AC Mains Frequency Range(s) 47 – 53 Hz Electrical Isolation 0-10V (Version) This input has optical isolation and is insulated from mains from Mains Control Dimmer 0-10V (0-5/20V) DC, 12V P.W.M, 1-10V POT. or 500K potentiometer Load Brightness Control Range 0% to 100% (0-97%* for typical Quality LEDs load)* Minimum Load 10-25W* (TE) & 5W (LE) Load Rating 7.6A max at 230-240V AC Mains Terminals 2 x 4-6 mm2 screw terminals 0/1-10V Terminals 2 x 4-6 mm2 screw terminals Weight ~450g Operating Temp. Range: 0 – 50⁰C 40 ºC to +50 ºC for output current ≤6.3A max 0 ºC to +40 ºC for output current >7.6A max Max. casing temperature Tc 80 ºC Operating Humidity Range 10% – 90% RH non condensing Thermal Protection NTC temperature limit is set to: Normal 125 °C Heavy Duty Model 135 °C Housing Material type Polycarbonate (UL94-HB) IP Rating IP60 Dim Device Type LE- Leading Edge: TE- Trailing Edge Safety Compliance AS/NZS 3100:2017 + VDE Components certificate Life Time Up to 100000 h Dimensions L x W x H (mm) 90 x 115 x 55 Note: 1. All parameters measured at 230-240V AC input, rated current and 25°C ambient temperature. 2. A driver is considered a component that will be operated in conjunction with final equipment such as (LED driver), if drivers are of poor quality it may interfere with proper operation. 3. The lights connected to the dimmer must not exceed 7.6A, the read value of the light, not the current voltage read by the measuring instrument, because the dimmer reduces the current / power to maintain green energy, otherwise the reading will be false and may damage the dimmer.