1-Pair Stuff 4604 Single Action Spring Hinge, 6″ X 4.5″
Single action spring hingeSpeed & tension adjustable6 inch X 4.5 inch
Garage Door Torsion Spring SINGLE RW .250 x 2 1/4″ ID x Select Length -USA MADE*
This Listing is for One Single .250 X 2 1/4″ (select the length) Right Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Right Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .250, Inside Diameter is 2 1/4″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cycles These Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)1 year Limited Warranty Against Premature Breakage Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay.CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Taymor B65000 Single Spring Crash Chain Door Guard 2PKS
Home View all listings About Contact Terms Sawblades Sockets Wrenches Hand Tools Router Bits Drill Bits Tape Measures Knives Hardware Menu Categories Air Tools Armstrong Tools Automotive Bath Hardware Buffing & Polishing Bungee Cords & Tie Downs Chisels & Punches Chucks & Keys Clamps & Vises DeWalt Door Hardware Drill Bits Electrical Extension Cords Files Flashlights Hammers Hand Tools Hole Saws Insert Bits Irwin Jig Saw Blades Knives & Blades Lighting Locks Measuring Tools Paint Supplies Pliers Power Tools Reciprocating Blades Router Bits Safety Sandpaper Saw Blades, Grinding Wheels Scissors & Crafts Screwdrivers & Nutdrivers Sockets Taps & Dies Tool Storage Torches Torx & Hex Keys Welding & Soldering Wrenches Other Taymor B65000 Single Spring Crash Chain Door Guard 2PKS Click Thumbnails to Enlarge Product description Taymor B65000 Single Spring Crash Chain Door Guard 2pcs. Single spring door chain with hold-up spring Heavy Duty Furnished w/”S” hooks & screws Material: Steel Finish: Zinc This item has calculated shipping. Shipping varies by carrier and the best rate does not show in the shopping cart. To get the best rate go to the Checkout. There will be a Delivery section that shows shipping options. Select the one you want to get the best rate. aeronca x 12 weiser south Payments Feedback Shipping Returns Payments Payments terms coming soon Feedback Feedback terms coming soon Shipping Shipping terms coming soon Returns Returns terms coming soon INTERNATIONAL SHIPPING 24 HR RESPONSE open monday-friday 24 HR Shipping open monday-friday Home View all listings About Contact Terms Copyright © 2018 Cripe Distributing. All Rights Reserved. eBay Templates Design by OCDesignsOnline Listing and template services provided by inkFrog
Wayne Dalton Garage Door TorqueMaster Plus 8′ Door 60#-69# Single Spring New
TorqueMaster Plus Replacement Springs 8′ High Door 60# – 69# Door Single Spring System One Right Spring Highest Rated Lifespan New Wayne Dalton Manufactured Springs American Made Replacement springs may be a different length than your original springs. The TorqueMaster Plus springs have a hexagon winding end with groves, are generally plastic ( not always), and were made generally after February 2007 (Not always). Your TorqueMaster tube (not included) contains a significant amount of factory information including the weight of the door. See the photos for an example of the factory label. If the label is not present the door will need to be weighed. Your spring come with the ends installed. The plastic sleeve around the spring is not included. Springs only, no other parts are included. The springs are coiled up and shipped in a box. Replacement springs may be slightly different than the original springs that came with the door. These are original Wayne Dalton factory springs, American made. Returns accepted. We have over 35 years experience in the garage door industry, have operated as professional Wayne Dalton installers and have the knowledge to help with your Wayne Dalton TorqueMaster spring replacement needs. Feel free to contact us. Orders of two or more may take longer to ship. Notice: Garage door installation and repair is dangerous and can result in serious injury or death. Springs and cables are under extreme tension and doors are extremely heavy. Qualified garage door technicians should perform installations, repairs and adjustments. Garage door installation, repair or adjustments done by you are at your own risk. You are assuming responsibility for use of this product. Signature Consulting, Inc. is not liable for any injuries or damages. You are agreeing to these terms by the purchase of this product.
Garage Door Torsion Spring SINGLE RW .192 x 1 3/4″ ID x Select Length -USA MADE*
This Listing is for One Right Wound .192 X 1 3/4″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes a single Right Wound Torsion Spring.1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .192, Inside Diameter is 1 3/4″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering. Step 1. is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size. Double check by measuring 20 coils and compare to the 20 coil measurement. If the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched (no gaps between the wires). Do not take your measurements on the ends where the wire goes over the cones are. The cones tend to stretch the wire apart causing gaps between the wires. Any gaps between the wires will not give an accurate measurement. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter (ID). If the spring is broken you can simply use a ruler to measure the inside of the broken end. If the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID; for instance P200 or P2000 will be stamped on the cones for a 2” ID and P175 for a 1 3/4″ ID. The most common sizes in residential springs are 1 3/4″ and 2″ (Raynor doors use a 2 ¼” ID). Step 3 is to measure the length of the spring. Measure the spring only; do not include the winding and stationary cones. If the spring is broken, measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and still wound, it will be longer by 2-3” than when it is relaxed. The proper way to measure for the length is to unwind the spring and then measure. Step 4 is only important if ordering a single spring. You will need to determine the wind direction of the spring (right hand wind {RW}) or left hand wind {LW}). Look at the third photo on this listing for an example of the two different spring wind directions. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay.CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICYReturns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Wayne Dalton Garage Door TorqueMaster Plus 7′ Door 60#-69# Single Spring New
TorqueMaster Plus Replacement Springs 7′ High Door 60# – 69# Door Single Spring System One Right Spring Highest Rated Lifespan New Wayne Dalton Manufactured Springs American Made Replacement springs may be a different length than your original springs. The TorqueMaster Plus springs have a hexagon winding end with groves, are generally plastic ( not always), and were made generally after February 2007 (Not always). Your TorqueMaster tube (not included) contains a significant amount of factory information including the weight of the door. See the photos for an example of the factory label. If the label is not present the door will need to be weighed. Your spring come with the ends installed. The plastic sleeve around the spring is not included. Springs only, no other parts are included. The springs are coiled up and shipped in a box. Replacement springs may be slightly different than the original springs that came with the door. These are original Wayne Dalton factory springs, American made. Returns accepted. We have over 35 years experience in the garage door industry, have operated as professional Wayne Dalton installers and have the knowledge to help with your Wayne Dalton TorqueMaster spring replacement needs. Feel free to contact us. Orders of two or more may take longer to ship. Notice: Garage door installation and repair is dangerous and can result in serious injury or death. Springs and cables are under extreme tension and doors are extremely heavy. Qualified garage door technicians should perform installations, repairs and adjustments. Garage door installation, repair or adjustments done by you are at your own risk. You are assuming responsibility for use of this product. Signature Consulting, Inc. is not liable for any injuries or damages. You are agreeing to these terms by the purchase of this product.
Garage Door Torsion Spring SINGLE RW .200 x 2″ ID x Select Length – USA MADE*
This Listing is for One Right Wound .200 X 2″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes a single Right Wound Torsion Spring.1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .200, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering. Step 1. is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size. Double check by measuring 20 coils and compare to the 20 coil measurement. If the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched (no gaps between the wires). Do not take your measurements on the ends where the wire goes over the cones are. The cones tend to stretch the wire apart causing gaps between the wires. Any gaps between the wires will not give an accurate measurement. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter (ID). If the spring is broken you can simply use a ruler to measure the inside of the broken end. If the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID; for instance P200 or P2000 will be stamped on the cones for a 2” ID and P175 for a 1 3/4″ ID. The most common sizes in residential springs are 1 3/4″ and 2″ (Raynor doors use a 2 ¼” ID). Step 3 is to measure the length of the spring. Measure the spring only; do not include the winding and stationary cones. If the spring is broken, measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and still wound, it will be longer by 2-3” than when it is relaxed. The proper way to measure for the length is to unwind the spring and then measure. Step 4 is only important if ordering a single spring. You will need to determine the wind direction of the spring (right hand wind {RW}) or left hand wind {LW}). Look at the third photo on this listing for an example of the two different spring wind directions. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay.CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICYReturns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Torsion Spring SINGLE RW .243 x 1 3/4″ ID x Select Length -USA MADE*
This Listing is for One Single .243 x 1 3/4″ (select the length) Right Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Right Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .243, Inside Diameter is 1 3/4″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Torsion Spring SINGLE LW .262 x 2″ ID x Select Length – USA MADE*
This Listing is for One Single .262 X 2″ (select the length) Left Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Left Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .262, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors, and if we don’t have it in stock can usually have it in a few days. If you are looking for a part and we don’t have it listed, just Email us and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Torsion Spring SINGLE LW .207 x 1.75″ ID x Select Length -USA MADE*
This Listing is for One Single Left Wound .207 X 1 3/4″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one (1) Left Wound Torsion SpringOne Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .207, Inside Diameter is 1 3/4″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size,double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.