Garage Door Torsion Springs PAIR .250 x 2″ ID x Select Length -USA MADE*
This Listing is for One Pair of .250 X 2″ (select the length) Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringsPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Pair of Springs (1 Right Wound, and 1 Left Wound)1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .250, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering. Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Garage Door Torsion Spring- SINGLE RW .241 x 2″ ID x 29 Inch
The Garage Door Torsion Spring is a modern-style unit made of black coated steel, designed to provide a smooth and efficient operation for your garage door.
Wayne Dalton Garage Door TorqueMaster Plus TorqueMaster One Replacement Springs
Wayne Dalton Garage Door TorqueMaster Plus & TorqueMaster One Replacement Springs 7′ and 8′ High Doors All Weights Available Double Spring System One Left Spring One Right SpringSingle Spring System One Left Spring Highest Rated Lifespan New Wayne Dalton Manufactured SpringsAmerican MadeChoose Height, Model (TorqueMaster One or TorqueMaster Plus), Double or Single and Weight Replacement springs may be a different length than your original springs. This is due to new, improved metals, and wire sizes. Simply identify your spring model; TorqueMaster One or TorqueMaster Plus from the photographs then select your door height, weight and single or double spring to find the spring you need! The TorqueMaster One springs have a rounded winding end with splines , are generally metal ( not always), and were made generally before February 2007 (Not always). The TorqueMaster Plus have a hexagon end with groves, are generally plastic (not always) and were made generally after February 2007 (Not always). Your TorqueMaster tube (not included) contains a significant amount of factory information including the weight of the door. See the photos for an example of the factory label. If the label is not present the door will need to be weighed. Your spring(s) come with the ends installed and a new plastic sleeve to reduce noise inside the tube. Springs only, no other parts are included. Replacement springs may be slightly different than the original springs that came with the door. These are original Wayne Dalton factory springs, American made. Returns accepted. We have over 35 years experience in the garage door industry, have operated as professional Wayne Dalton installers and have the knowledge to help with your Wayne Dalton TorqueMaster spring replacement needs. Feel free to contact us.Please Note: Quantities of 3 or more may require extra shipping time. Notice: Garage door installation and repair is dangerous and can result in serious injury or death. Springs and cables are under extreme tension and doors are extremely heavy. Qualified garage door technicians should perform installations, repairs and adjustments. Garage door installation, repair or adjustments done by you are at your own risk. You are assuming responsibility for use of this product. Signature Consulting, Inc. is not liable for any injuries or damages. You are agreeing to these terms by the purchase of this product.
Garage Door Torsion Spring- SINGLE RW .218 x 2″ ID x Select Length – USA MADE*
This Listing is for One Single .218 X 2″ (select the length) Right Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Right Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .218, Inside Diameter is 2″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size,double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions. If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay. CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. Sellebrity Analytics RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
YOTOOLGDS Single Garage Door Torsion Spring (L&R), Various Sizes, Non-Slip Bars
The YOTOOLGDS Single Garage Door Torsion Spring is a durable and reliable hardware option for garages. Made of steel, these torsion springs are suitable for use with garage doors and come in various sizes to fit different door types. The non-slip bars provide added security and stability, making them a practical choice for maintaining the functionality of your garage door. Browse our selection to find the perfect fit for your home.
Pair Garage Torsion Springs .207 X 1-3/4″ (1.75) ID X (VARIOUS LENGTHS) With WB
Pair of Garage Door Torsion Springs .207 Wire x 1-3/4″ Inner Diameter x (Various Lengths) w/ Winding Bars and Bushing Torsion springs are the most common type of springs used on garage doors. It is critical to have the correct size springs in order to maintain a properly balanced garage door. When ordering replacement springs make sure you are ordering the correct size This will ensure you get the correct springs. Please do not guess which springs the garage door needs. The door will not balance properly and may cause damage or injury. Please be sure to install springs correctly, WHILE STANDING INSIDE THE GARAGE LOOKING UP AT THE TORSION TUBE, the right wind spring (red mark on winding cone) goes on the LEFT SIDE of center bracket, and the left wind spring (black mark on winding cone) goes on the RIGHT SIDE of the center bracket, Make sure you know what you are doing, if springs are put on backwards and ruined due to improper installation, refunds will be denied. WINDING BARS AND BUSHING ARE PACKED INSIDE THE SPRINGS.Includes:Torsion springs (left and right)Winding and stationary cones installedPlastic center bushingWinding barsFeatures:Corrosion resistantOil temperedWARNING: Torsion springs, extension springs, and related door hardware can cause serious injury or death if not handled and installed properly. Professional installation is recommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work.Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.About UsWe are a garage door wholesaler. We carry a wide selection of parts for all brands. We are continually looking to add new parts to our inventory. If you need a part you do not see just ask.Contact UsPlease feel free to contact us using eBay messages with any questions, comments or concerns. We will reply as soon as possible. Make sure to include as much information as possible like model numbers.ReturnsYour order may be returned within 30 days of the sale date. Shipping is not refundable. Returns with free shipping will have the actual shipping cost deducted from the refund. ShippingWe pride ourselves with fast shipping. Most orders placed by 3PM CST ship the same day. Some products require additional prep time. Use the shipping and payments tab to see available shipping services and cost. We recommend picking Priority Mail and UPS services which are all insured. First class mail is not insured. Track Page Views With Auctiva’s FREE Counter
Pair Of Garage Door Torsion Springs .273 X 2″ ID X (Various Lengths) With WB
Pair of Garage Door Torsion Springs .273 Wire x 2″ Inner Diameter x (Various Lengths) w/ Winding Bars and Bushing Torsion springs are the most common type of springs used on garage doors. It is critical to have the correct size springs in order to maintain a properly balanced garage door. When ordering replacement springs make sure you are ordering the correct size This will ensure you get the correct springs. Please do not guess which springs the garage door needs. The door will not balance properly and may cause damage or injury. Please be sure to install springs correctly, WHILE STANDING INSIDE THE GARAGE LOOKING UP AT THE TORSION TUBE, the right wind spring (red mark on winding cone) goes on the LEFT SIDE of center bracket, and the left wind spring (black mark on winding cone) goes on the RIGHT SIDE of the center bracket, Make sure you know what you are doing, if springs are put on backwards and ruined due to improper installation, refunds will be denied. WINDING BARS AND BUSHING ARE PACKED INSIDE THE SPRINGS.Includes:Torsion springs (left and right)Winding and stationary cones installedPlastic center bushingWinding barsFeatures:Corrosion resistantOil temperedWARNING: Torsion springs, extension springs, and related door hardware can cause serious injury or death if not handled and installed properly. Professional installation is recommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work.Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.Wire Size Chart (Measure 10 and 20 coils across, all touching, outside to outside)Length of 10 CoilsLength of 20 CoilsWire Size1 1/4″2 1/2″0.1251 3/8″2 3/4″0.1351 7/16″2 7/8″0.1421 1/2″3″0.14831 9/16″3 1/8″0.15621 5/8″3 1/4″0.1621 11/16″3 3/8″0.1701 3/4″3 1/2″0.1771 7/8″3 3/4″0.18751 15/16″3 7/8″0.1922 1/16″4 1/8″0.2072 3/16″4 3/8″0.21872 1/4″4 1/2″0.22532 5/164 5/8″0.23432 7/16″4 7/8″0.24372 1/2″5″0.2502 5/8″5 1/4″0.26252 3/4″5 1/2″0.2732 13/16″5 5/8″0.2832 7/8″5 3/4″0.2892 15/16″5 7/8″0.2953 1/16″6 1/8″0.30653 1/8″6 1/4″0.31253 3/16″6 3/8″0.31953 5/16″6 5/8″0.331About UsWe are a garage door wholesaler. We carry a wide selection of parts for all brands. We are continually looking to add new parts to our inventory. If you need a part you do not see just ask.Contact UsPlease feel free to contact us using eBay messages with any questions, comments or concerns. We will reply as soon as possible. Make sure to include as much information as possible like model numbers.ReturnsYour order may be returned within 30 days of the sale date. Shipping is not refundable. Returns with free shipping will have the actual shipping cost deducted from the refund. ShippingWe pride ourselves with fast shipping. Most orders placed by 3PM CST ship the same day. Some products require additional prep time. Use the shipping and payments tab to see available shipping services and cost. We recommend picking Priority Mail and UPS services which are all insured. First class mail is not insured. Track Page Views With Auctiva’s FREE Counter On Jul 22, 2022 at 17:22:47 PDT, seller added the following information:
Pair Garage Torsion Springs .225 X 1-3/4″ (1.75) ID X (VARIOUS LENGTHS) With WB
Pair of Garage Door Torsion Springs .225 Wire x 1-3/4″ Inner Diameter x (Various Lengths) w/ Winding Bars and Bushing Torsion springs are the most common type of springs used on garage doors. It is critical to have the correct size springs in order to maintain a properly balanced garage door. When ordering replacement springs make sure you are ordering the correct size This will ensure you get the correct springs. Please do not guess which springs the garage door needs. The door will not balance properly and may cause damage or injury. Please be sure to install springs correctly, WHILE STANDING INSIDE THE GARAGE LOOKING UP AT THE TORSION TUBE, the right wind spring (red mark on winding cone) goes on the LEFT SIDE of center bracket, and the left wind spring (black mark on winding cone) goes on the RIGHT SIDE of the center bracket, Make sure you know what you are doing, if springs are put on backwards and ruined due to improper installation, refunds will be denied. WINDING BARS AND BUSHING ARE PACKED INSIDE THE SPRINGS.Includes:Torsion springs (left and right)Winding and stationary cones installedPlastic center bushingWinding barsFeatures:Corrosion resistantOil temperedWARNING: Torsion springs, extension springs, and related door hardware can cause serious injury or death if not handled and installed properly. Professional installation is recommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work.Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.About UsWe are a garage door wholesaler. We carry a wide selection of parts for all brands. We are continually looking to add new parts to our inventory. If you need a part you do not see just ask.Contact UsPlease feel free to contact us using eBay messages with any questions, comments or concerns. We will reply as soon as possible. Make sure to include as much information as possible like model numbers.ReturnsYour order may be returned within 30 days of the sale date. Shipping is not refundable. Returns with free shipping will have the actual shipping cost deducted from the refund. ShippingWe pride ourselves with fast shipping. Most orders placed by 3PM CST ship the same day. Some products require additional prep time. Use the shipping and payments tab to see available shipping services and cost. We recommend picking Priority Mail and UPS services which are all insured. First class mail is not insured. Track Page Views With Auctiva’s FREE Counter