10″ Clear Standard Whole House Water Filter System 4 Sediment 10 Micron Filters
Untitled Document 10 Inches Transparent Standard Whole House Water Filter System with Presser Relief Valve, 3/4” Inlet/Outlet Brass Port and Yearly Supply (4) Sediment Cartridges 10 Micron Product Description DURABLE STRUCTURE: 10” Transparent Standard Housing is proper for heavy sediment applications. The housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. 10” Standard 10 Micron Sediment Filters Used for effectively removing most sediments from water POINT OF USE: This System for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances. Keeps water fresh by reducing sediment, scale, rust, dirt, sands, and silt EASY TO OPERATE: There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Unique cap design allow quickly and easy to remove housing to replace cartridges. Transparent housing body allows visually to determine when cartridge should be changed 10 MICRON SEDIMENT CARTRIDGE is wrapped and sealed and meets NSF Standards and Regulations. Dimensions: 10” x 2.5”. WELL-MATCHED: Dupont PFC5002, WFPFC5002, 3M CFS110, AP110-NP, AP101S, AP101T, Aqua Pure AP110, AP11T, AP51T, Hydronix SGC-25-1005, Culligan P5, P5-D, P5A, OmniFilter RS14-SD and RS14-SS, GE FXUSC, Aquaboon S-5M, Manitowoc K-00173, Whirlpool WHKF-GD05, American Plumber W5P, Pureplus PP10-05, however for best preferment use only original RONAQUA CARTRIDGES WELL-MATCHED FOLLOWING HOUSINGS SYSTEMS: DuPont WFPF38001C, WFPF13003B, Culligan WTR Filter HF-360A and HF-150A, American Plumber WC34-PR, Geekpure RO5-FH10, Hydronix HF3-10CLBK34, EcoPure EPW2 Description: The 10″ Transparent Standard Housing for Whole House Water Filtration System with 3/4″ Inlet / Outlet Brass Ports (RA-125-10) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The transparent housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The blue cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief valve on the outlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. Filter Cartridges Included in this Set are Melt-blown Four Layers Filtration Polypropylene Sediment Filter (4 pack) A Sediment Water Filter removes the physical debris and impurities from your water. The sediment filter has tiny holes through which water is able to pass, however the unwanted particles are not. As these particles come in different sizes, so do the filters. The filter sizes are measured in microns, the smaller the micron measurement, the smaller the holes in the filter, allowing to hold back the smallest of particles. Generally, for water that is more visibly polluted, containing larger particles, a sediment filter of a larger size (such as 20 or 50 microns) is recommended in the first stage of installation to prevent the clogging of the next stage(s) of filters. This sediment filter is often the first filter installed in the Reverse Osmosis circuit and acts as a net as it catches unwanted particles, including sand, dirt, silt, rust, and other fine particles. Sediment filters are made of fine melted polypropylene, which is then blown and spun into a cylinder-like form. Polypropylene is a substance that is resistant to chemical solvents, bases, and acids. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, to perform better and for longer periods of time. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. Multi-layer Gradient Filtration Outer Zone Mid Zone Inner Zone Innermost Zone These Sediment Water Filters Intercept all Following Impurities Rust & Corrosion- Rust is a type of corrosion. Corrosion is the process by which certain materials, metals and non-metals, deteriorate as a result of oxidation. Rusting is oxidation of iron in the presence of air and moisture. … Corrosion requires surface exposure to air or chemicals Coarse Sand is our concrete sand that is washed and screened to a larger grit than our Fine Washed Sand (masonry sand). Coarse Sand is used with aggregate, water, and cement in the production of ready-mix concrete. Hard Scale causes a variety of problems in the home. Stains are probably the most noticeable result of hard water scale. Stains appear in toilets, sinks, and showers. Some hardwater scale are less noticeable, such as scale build up in pipes and in appliances which can cause costly repairs or the need to replace appliances. Fine Sand is very fine, screened sand that is typically tan in color. This type of sand is commonly used as base sand for above ground swimming pools, paving stones, sidewalk blocks and retaining walls. It is alternately used in stucco and cement applications. Particles is a small localized object to which can be ascribed several physical or chemical properties, such as volume, density, or mass. They vary greatly in size or quantity, from subatomic particles like the electron, to microscopic particles like atoms and molecules, to macroscopic particles like powders and other granular materials. Particles can also be used to create scientific models of even larger objects depending on their density, such as humans moving in a crowd or celestial bodies in motion. Sediment is a naturally occurring material that is broken down by processes of weathering and erosion, and is subsequently transported by the action of wind, water, or ice or by the force of gravity acting on the particles. For example, sand and silt can be carried in suspension in river water and on reaching the sea bed deposited by sedimentation; if buried, they may eventually become sandstone and siltstone (sedimentary rocks) through lithification. Sediments are most often transported by water (fluvial processes), but also wind (aeolian processes) and glaciers. Beach sands and river channel deposits are examples of fluvial transport and deposition, though sediment also often settles out of slow-moving or standing water in lakes and oceans. Desert sand dunes and loess are examples of aeolian transport and deposition. Glacial moraine deposits and till are ice-transported sediments. Dirt is unclean matter, especially when in contact with a person’s clothes, skin or possessions. Common types of dirt include: Dust: a general powder of organic or mineral matter; Filth: foul matter such as excrement; Grime: a black, ingrained dust such as soot; Soil: the mix of clay, sand, and humus which lies on top of bedrock. Silt is granular material of a size between sand and clay, whose mineral origin is quartz & feldspar. Silt may occur as a soil or as sediment mixed in suspension with water and soil in a body of water such as a river. It may also exist as soil deposited at the bottom of a water body, like mudflows from landslides. Silt has a moderate specific area with a typically non-sticky, plastic feel. Silt usually has a floury feel when dry, and a slippery feel when wet. Silt can be visually observed with a hand lens, exhibiting a sparkly appearance. It also can be felt by the tongue as granular when placed on the front teeth (even when mixed with clay particles). Specifications: Filter Type Fine Melted Polypropylene 10 MICRON Flow Rate 5 GPM Unit Height IN/CM 12.5 IN/31.75 CM Operating Temperature 40°F (4.4°C) – 125°F (51.7°C) Unit Length IN/CM 5.125 IN/13.02 CM Operating Pressure 20 PSI (1.4 bar) – 60 PSI (4.5 bar) Unit Width IN/CM 5.125 IN/13.02 CM Cartridge Lifetime Replace two or three times a year – depending on your water quality Inlet/Outlet Ports 3/4″ NPT Bress Cartridge Packaging This filter is wrapped and sealed and meets NSF (National Science Foundation)
½ Cubic Ft Water Softener Resin 10% Cross Linked 100% Ion Exchange High Capacity
A whole house filter, softener, and a reverse osmosis system. Great for Replacing Resin or Adding on to Water Softening Systems. We are committed to bringing you the best water system you can buy at the most competitive prices.
Aquasure Harmony Series Water Softener w/ Digital Control Head – 48,000 Grain
Aquasure Harmony Series Whole House Water Softener w/ Digital Control Head – 48,000 Grain System Highlights Reduces hardness in the water, and eliminates scale, spot build up for the entire home. Rated to treat 64,000 Grains of Hardness by removing skin damaging hard minerals like iron and magnesium that clog up the skin pore and cost irritation. Equipped with Aquatrol Advanced Digital On-Demand Meter Control Head that calculates the amount of water it treated and backwash as needed. Saving hundreds of gallons of water and lessen the need for salt replenishment. Featured, time delayed, metered and manual double backwash for optimum regeneration, cleaning, and performance. Every Aquasure Water Softener is constructed of High strength corrosion resistant fiberglass lined polyethylene tank, durable bypass valve, and premium grade resin. It also comes with 5-year manufacturer warranty. Product Overview TThe Aquasure AS-HS64D Harmony Series of Whole House Water Softening System is built to provide Soft, scale and spot free water for the entire house. The Harmony AS-HS48D can treat up to 48,000 Grain of hardness, perfect for the household size of 3-4 bathrooms and up to 5 people. Its built-in advanced digital control console allows precise backwashing only when it’s needed, saving hundreds of gallons of water. Product Features SOFT, SCALE FREE WATER Aquasure Harmony Series whole house water softener reduces hardness in the water and eliminates scale, spot build up for the entire home. HEALTHY, VIBRANT SKIN Softened water is gentler on the skin because it removes skin damaging hard minerals like iron and magnesium that clog up the skin pore and cost irritation. It also reduces the need to rely on expensive skincare products as skin are naturally healthier. WORK EFFORTLESS All the water appliances now work more effortless and also more efficient as softer water reduces the amount of detergent and energy needed to perform REDUCE MAINTENANCE & REPAIR COST Protects your pipes and plumbing fixtures from clogs, corrosions and increase its longevity, while reducing the need for maintenance and repair BUILT FOR PERFORMANCE Aquasure Whole House Water Softener is equipped with fiber-reinforced polymer bypass valve, Digital control head console with double backwash feature for optimum regeneration, cleaning, and efficiency. PREMIUM QUALITY & DEPENDABILITY Aquasure Harmony Series of whole house water softener comes with premium grade resin, and durable high strength corrosion resistant fiberglass lined polyethylene tank. It also comes with 5-year warranty and lifetime tech support if you ever need it.
152003 AMERICAN PLUMBER WVC34 FILTER VALVE IN HEAD 3/4inch CLEAR WITH PRESSURE
Our durable line of. Valve-in-head (vih) closes both the inlet and outlet port simultaneously for quick change out. lead, cysts, and organic and chemical contaminants. Pressure relief button. hardness, chlorine taste & odor, and bad taste & odor, as well as reduction of.
Kinetico Model 100 Used Softener Head W/ Remote Tank Base For Parts
Sold as is for parts. Removed from a house. All sales are final. No returns.
Reconditioned 01-0130-83 Culligan Genuine OEM Seal Pack CUG01-0130-83
01-0130-83 Culligan Genuine OEM Seal Pack CUG01-0130-83 Reconditioned. See images of actual part you will receive. Inner and outer seals in excellent condition.
Fleck 9100 SXT Metered 24k Twin Alternating Water Softener 24/7 Soft Water
Fleck 9100 SXT Metered 24k Twin Alternating Water Softener 24/7 Soft WaterDESCRIPTION**Ships Loaded with the Resin in the Tank** NEW Fleck 9100SXT Water Softener with Free Shipping! AVAILABLE M-F DURING INSTALLATION AND PROGRAMMING!!! We look forward to helping our customers. Thanks Doug Aplus Water LLC We have warehouses in Ohio, Florida and Arizona to expedite shipping times!!! Never lose programming during power outage!!! Series 9100 Twin-Alternating Conditioners • Light Commercial/Heavy Residential WORKS GREAT FOR: • Car Washes • Club Houses• Factories • Laundromats• Large Homes • Office Buildings • Restaurants Twin tanks provide continuous soft water. With a twin-tank system featuring the new Fleck 9100 valve, customers benefit from soft water 24 hours a day, seven days a week. That’s because the second tank of soft water acts as a backup, ready to immediately provide soft water once 100% of the first tank is used. While the second tank is in service, the first tank regenerates, giving you all the advantages of continuous soft water. The 9100SXT valve has been engineered and tested to withstand the equivalent of 27 years of uninterrupted daily use. 15% savings in both water and salt. Unlike preset systems, the twin-tank system regenerates with soft water only when necessary. Plus it uses 100% of the tank in service. The end result? Fifteen percent savings in both water and salt.** ** Compared to a system with meter delayed regeneration and the reserve set at 30% of the system capacity, provided that half of the reserve capacity is unused. Only pennies per day to operate. How the Twin-Tank Softener works. Water Softening Process Hard water enters the tank in service, and fills it. As it passes through the resin, the hard water ions are attracted to the resin. By the time the water gets to the bottom of the tank, it’s soft. Regeneration Process When the resin becomes saturated with hard water ions, the tank goes into regeneration. Brine water is injected into the tank and rinses the hard water ions off the resin and down the drain. Once the resin is free of the hard water ions, fresh, soft water backwashes all the brine water out, leaving the tank ready for service. FLECK 9100SXT TWIN ALTERNATING METERED WATER SOFTENER 48,000 GRAIN CAPACITY PER TANK Complete water softener comes with : 1.5 CUBIC FEET OF RESIN, 24,000 GRAIN CAPACITY PER TANK (TOTAL OF 48,000 GRAINS), FLECK 9100SXT CONTROLLER, TWO MINERAL TANKS, Salt Tank, BYPASS, COMPLETE SYSTEM 50X18X62 inches, 3/4 inch or 1 inch connections, (14x14x36) BRINE TANK w/safety float, AVAILABLE IN BLUE, BLACK OR ALMOND You can select options in the comment section during checkout or by email or phone prior or immediately after the sale. 3/4 inch bypass is the default if not specified by the customer and blue tanks is the default if not specified by the customer. Copyright © Aplus Water LLC 2020 Notice: consumer is responsible for following any state and/or local regulations and plumbing codes pertinent to the purchase, installation and operation of our products.See our other items**Ships Loaded with the Resin in the Tank** NEW Fleck 9100SXT Water Softener with Free Shipping! AVAILABLE M-F DURING INSTALLATION AND PROGRAMMING!!! We look forward to helping our customers. Thanks Doug Aplus Water LLC We have warehouses in Ohio, Florida and Arizona to expedite shipping times!!! Never lose programming during power outage!!! Series 9100 Twin-Alternating Conditioners • Light Commercial/Heavy Residential WORKS GREAT FOR: • Car Washes • Club Houses• Factories • Laundromats• Large Homes • Office Buildings • Restaurants Twin tanks provide continuous soft water. With a twin-tank system featuring the new Fleck 9100 valve, customers benefit from soft water 24 hours a day, seven days a week. That’s because the second tank of soft water acts as a backup, ready to immediately provide soft water once 100% of the first tank is used. While the second tank is in service, the first tank regenerates, giving you all the advantages of continuous soft water. The 9100SXT valve has been engineered and tested to withstand the equivalent of 27 years of uninterrupted daily use. 15% savings in both water and salt. Unlike preset systems, the twin-tank system regenerates with soft water only when necessary. Plus it uses 100% of the tank in service. The end result? Fifteen percent savings in both water and salt.** ** Compared to a system with meter delayed regeneration and the reserve set at 30% of the system capacity, provided that half of the reserve capacity is unused. Only pennies per day to operate. How the Twin-Tank Softener works. Water Softening Process Hard water enters the tank in service, and fills it. As it passes through the resin, the hard water ions are attracted to the resin. By the time the water gets to the bottom of the tank, it’s soft. Regeneration Process When the resin becomes saturated with hard water ions, the tank goes into regeneration. Brine water is injected into the tank and rinses the hard water ions off the resin and down the drain. Once the resin is free of the hard water ions, fresh, soft water backwashes all the brine water out, leaving the tank ready for service. FLECK 9100SXT TWIN ALTERNATING METERED WATER SOFTENER 48,000 GRAIN CAPACITY PER TANK — Complete water softener comes with : — 1.5 CUBIC FEET OF RESIN, — 24,000 GRAIN CAPACITY PER TANK (TOTAL OF 48,000 GRAINS), — FLECK 9100SXT CONTROLLER, — TWO MINERAL TANKS, — Salt Tank, BYPASS, — COMPLETE SYSTEM 50X18X62 inches, — 3/4 inch or 1 inch connections, — (14x14x36) BRINE TANK w/safety float, — AVAILABLE IN BLUE, BLACK OR ALMOND — You can select options in the comment section during checkout or by email or phone prior or immediately after the sale. 3/4 inch bypass is the default if not specified by the customer and blue tanks is the default if not specified by the customer. Fleck 9100 SXT Metered 24k Twin Alternating Water Softener 24/7 Soft Water**Ships Loaded with the Resin in the Tank** NEW Fleck 9100SXT Water Softener with Free Shipping! AVAILABLE M-F DURING INSTALLATION AND PROGRAMMING!!! We look forward to helping our customers. Thanks Doug Aplus Water LLC We have warehouses in Ohio, Florida and Arizona to expedite shipping times!!! Never lose programming during power outage!!! Series 9100 Twin-Alternating Conditioners • Light Commercial/Heavy Residential WORKS GREAT FOR: • Car Washes • Club Houses• Factories • Laundromats• Large Homes • Office Buildings • Restaurants Twin tanks provide continuous soft water. With a twin-tank system featuring the new Fleck 9100 valve, customers benefit from soft water 24 hours a day, seven days a week. That’s because the second tank of soft water acts as a backup, ready to immediately provide soft water once 100% of the first tank is used. While the second tank is in service, the first tank regenerates, giving you all the advantages of continuous soft water. The 9100SXT valve has been engineered and tested to withstand the equivalent of 27 years of uninterrupted daily use. 15% savings in both water and salt. Unlike preset systems, the twin-tank system regenerates with soft water only when necessary. Plus it uses 100% of the tank in service. The end result? Fifteen percent savings in both water and salt.** ** Compared to a system with meter delayed regeneration and the reserve set at 30% of the system capacity, provided that half of the reserve capacity is unused. Only pennies per day to operate. How the Twin-Tank Softener works. Water Softening Process Hard water enters the tank in service, and fills it. As it passes through the resin, the hard water ions are attracted to the resin. By the time the water gets to the bottom of the tank, it’s soft. Regeneration Process When the resin becomes saturated with hard water ions, the tank goes into regeneration. Brine water is injected into the tank and rinses the hard water ions off the resin and down the drain. Once the resin is free of the hard water ions, fresh, soft water backwashes all the brine water out, leaving the tank ready for service. FLECK 9100SXT TWIN ALTERNATING METERED WATER SOFTENER 48,000 GRAIN CAPACITY PER TANK Complete water softener comes with : 1.5 CUBIC FEET OF RESIN, 24,000 GRAIN CAPACITY PER TANK (TOTAL OF 48,000 GRAINS), FLECK 9100SXT CONTROLLER, TWO MINERAL TANKS, Salt Tank, BYPASS, COMPLETE SYSTEM 50X18X62 inches, 3/4 inch or 1 inch connections, (14x14x36) BRINE TANK w/safety float, AVAILABLE IN BLUE, BLACK OR ALMOND You can select options in the comment section during checkout or by email or phone prior or immediately after the sale. 3/4 inch bypass is the default if not specified by the customer and blue tanks is the default if not specified by the customer. See our other itemsDESCRIPTION Copyright © Aplus Water LLC 2020 Notice: consumer is responsible for following any state and/or local regulations and plumbing codes pertinent to the purchase, installation and operation of our products.**Ships Loaded with the Resin in the Tank** NEW Fleck 9100SXT Water Softener with Free Shipping! AVAILABLE M-F DURING INSTALLATION AND PROGRAMMING!!! We look forward to helping our customers. Thanks Doug Aplus Water LLC We have warehouses in Ohio, Florida and Arizona to expedite shipping times!!! Never lose programming during power outage!!! Series 9100 Twin-Alternating Conditioners • Light Commercial/Heavy Residential WORKS GREAT FOR: • Car Washes • Club Houses• Factories • Laundromats• Large Homes • Office Buildings • Restaurants Twin tanks provide continuous soft water. With a twin-tank system featuring the new Fleck 9100 valve, customers benefit from soft water 24 hours a day, seven days a week. That’s because the second tank of soft water acts as a backup, ready to immediately provide soft water once 100% of the first tank is used. While the second tank is in service, the first tank regenerates, giving you all the advantages of continuous soft water. The 9100SXT valve has been engineered and tested to withstand the equivalent of 27 years of uninterrupted daily use. 15% savings in both water and salt. Unlike preset systems, the twin-tank system regenerates with soft water only when necessary. Plus it uses 100% of the tank in service. The end result? Fifteen percent savings in both water and salt.** ** Compared to a system with meter delayed regeneration and the reserve set at 30% of the system capacity, provided that half of the reserve capacity is unused. Only pennies per day to operate. How the Twin-Tank Softener works. Water Softening Process Hard water enters the tank in service, and fills it. As it passes through the resin, the hard water ions are attracted to the resin. By the time the water gets to the bottom of the tank, it’s soft. Regeneration Process When the resin becomes saturated with hard water ions, the tank goes into regeneration. Brine water is injected into the tank and rinses the hard water ions off the resin and down the drain. Once the resin is free of the hard water ions, fresh, soft water backwashes all the brine water out, leaving the tank ready for service. FLECK 9100SXT TWIN ALTERNATING METERED WATER SOFTENER 48,000 GRAIN CAPACITY PER TANK Complete water softener comes with : 1.5 CUBIC FEET OF RESIN, 24,000 GRAIN CAPACITY PER TANK (TOTAL OF 48,000 GRAINS), FLECK 9100SXT CONTROLLER, TWO MINERAL TANKS, Salt Tank, BYPASS, COMPLETE SYSTEM 50X18X62 inches, 3/4 inch or 1 inch connections, (14x14x36) BRINE TANK w/safety float, AVAILABLE IN BLUE, BLACK OR ALMOND You can select options in the comment section during checkout or by email or phone prior or immediately after the sale. 3/4 inch bypass is the default if not specified by the customer and blue tanks is the default if not specified by the customer.
Housing Wrench for 10″ Clear Standard Whole House Water Filter System
Housing Wrench for 10″ Clear Standard Whole House Water Filter System or Dual Whole House Water Filter Purifier
10″ Clear Standard Whole House Water Filter System 25 Micron Sediment Filter
Untitled Document 10 Inches Transparent Standard Whole House Water Filter System with Presser Relief Valve, 3/4” Inlet/Outlet Brass Port and Sediment Cartridge 25 Micron Product Description DURABLE STRUCTURE: 10” Transparent Standard Housing is proper for heavy sediment applications. The housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. 10” Standard 25 Micron Sediment Filters Used for effectively removing most sediments from water POINT OF USE: This System for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances. Keeps water fresh by reducing sediment, scale, rust, dirt, sands, and silt EASY TO OPERATE: There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Unique cap design allow quickly and easy to remove housing to replace cartridges. Transparent housing body allows visually to determine when cartridge should be changed 25 MICRON SEDIMENT CARTRIDGE is wrapped and sealed and meets NSF Standards and Regulations. Dimensions: 10” x 2.5”. WELL-MATCHED: Dupont PFC5002, WFPFC5002, 3M CFS110, AP110-NP, AP101S, AP101T, Aqua Pure AP110, AP11T, AP51T, Hydronix SGC-25-1005, Culligan P5, P5-D, P5A, OmniFilter RS14-SD and RS14-SS, GE FXUSC, Aquaboon S-5M, Manitowoc K-00173, Whirlpool WHKF-GD05, American Plumber W5P, Pureplus PP10-05, however for best preferment use only original RONAQUA CARTRIDGES WELL-MATCHED FOLLOWING HOUSINGS SYSTEMS: DuPont WFPF38001C, WFPF13003B, Culligan WTR Filter HF-360A and HF-150A, American Plumber WC34-PR, Geekpure RO5-FH10, Hydronix HF3-10CLBK34, EcoPure EPW2 Description: The 10″ Transparent Standard Housing for Whole House Water Filtration System with 3/4″ Inlet / Outlet Brass Ports (RA-125-10) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The transparent housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The blue cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief valve on the outlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. Filter Cartridges Included in this Set are Melt-blown Four Layers Filtration Polypropylene Sediment Filter A Sediment Water Filter removes the physical debris and impurities from your water. The sediment filter has tiny holes through which water is able to pass, however the unwanted particles are not. As these particles come in different sizes, so do the filters. The filter sizes are measured in microns, the smaller the micron measurement, the smaller the holes in the filter, allowing to hold back the smallest of particles. Generally, for water that is more visibly polluted, containing larger particles, a sediment filter of a larger size (such as 20 or 50 microns) is recommended in the first stage of installation to prevent the clogging of the next stage(s) of filters. This sediment filter is often the first filter installed in the Reverse Osmosis circuit and acts as a net as it catches unwanted particles, including sand, dirt, silt, rust, and other fine particles. Sediment filters are made of fine melted polypropylene, which is then blown and spun into a cylinder-like form. Polypropylene is a substance that is resistant to chemical solvents, bases, and acids. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, to perform better and for longer periods of time. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. Multi-layer Gradient Filtration Outer Zone Mid Zone Inner Zone Innermost Zone These Sediment Water Filters Intercept all Following Impurities Rust & Corrosion- Rust is a type of corrosion. Corrosion is the process by which certain materials, metals and non-metals, deteriorate as a result of oxidation. Rusting is oxidation of iron in the presence of air and moisture. … Corrosion requires surface exposure to air or chemicals Coarse Sand is our concrete sand that is washed and screened to a larger grit than our Fine Washed Sand (masonry sand). Coarse Sand is used with aggregate, water, and cement in the production of ready-mix concrete. Hard Scale causes a variety of problems in the home. Stains are probably the most noticeable result of hard water scale. Stains appear in toilets, sinks, and showers. Some hardwater scale are less noticeable, such as scale build up in pipes and in appliances which can cause costly repairs or the need to replace appliances. Fine Sand is very fine, screened sand that is typically tan in color. This type of sand is commonly used as base sand for above ground swimming pools, paving stones, sidewalk blocks and retaining walls. It is alternately used in stucco and cement applications. Particles is a small localized object to which can be ascribed several physical or chemical properties, such as volume, density, or mass. They vary greatly in size or quantity, from subatomic particles like the electron, to microscopic particles like atoms and molecules, to macroscopic particles like powders and other granular materials. Particles can also be used to create scientific models of even larger objects depending on their density, such as humans moving in a crowd or celestial bodies in motion. Sediment is a naturally occurring material that is broken down by processes of weathering and erosion, and is subsequently transported by the action of wind, water, or ice or by the force of gravity acting on the particles. For example, sand and silt can be carried in suspension in river water and on reaching the sea bed deposited by sedimentation; if buried, they may eventually become sandstone and siltstone (sedimentary rocks) through lithification. Sediments are most often transported by water (fluvial processes), but also wind (aeolian processes) and glaciers. Beach sands and river channel deposits are examples of fluvial transport and deposition, though sediment also often settles out of slow-moving or standing water in lakes and oceans. Desert sand dunes and loess are examples of aeolian transport and deposition. Glacial moraine deposits and till are ice-transported sediments. Dirt is unclean matter, especially when in contact with a person’s clothes, skin or possessions. Common types of dirt include: Dust: a general powder of organic or mineral matter; Filth: foul matter such as excrement; Grime: a black, ingrained dust such as soot; Soil: the mix of clay, sand, and humus which lies on top of bedrock. Silt is granular material of a size between sand and clay, whose mineral origin is quartz & feldspar. Silt may occur as a soil or as sediment mixed in suspension with water and soil in a body of water such as a river. It may also exist as soil deposited at the bottom of a water body, like mudflows from landslides. Silt has a moderate specific area with a typically non-sticky, plastic feel. Silt usually has a floury feel when dry, and a slippery feel when wet. Silt can be visually observed with a hand lens, exhibiting a sparkly appearance. It also can be felt by the tongue as granular when placed on the front teeth (even when mixed with clay particles). Specifications: Filter Type Fine Melted Polypropylene 25 MICRON Flow Rate 5 GPM Unit Height IN/CM 12.5 IN/31.75 CM Operating Temperature 40°F (4.4°C) – 125°F (51.7°C) Unit Length IN/CM 5.125 IN/13.02 CM Operating Pressure 20 PSI (1.4 bar) – 60 PSI (4.5 bar) Unit Width IN/CM 5.125 IN/13.02 CM Cartridge Lifetime Replace two or three times a year – depending on your water quality Inlet/Outlet Ports 3/4″ NPT Bress Cartridge Packaging This filter is wrapped and sealed and meets NSF (National Science Foundation)
Nozzle And Venturi Assembly 7187065 For Kenmore,Whirlpool Water Softeners
Nozzle and Venturi Assembly – 7187065. This part fits many models of Kenmore, Whirlpool. Fuel system.