Ultra Custom Pools

Item Tag: 1 Gallon

Professional concrete floor finish high gloss 1 Gal quick drying acrylic (520)

Normal 0 false false false EN-US JA X-NONE UBQ Industries – Active Elements™ Advance Protect and Shine Acrylic Floor Finish Active Elements™ – Protect & Shine is a high gloss long lasting and renewable maintenance coat for interior decorative concrete floors. Protect & Shine is a rapid return to service product making it ideal for retail and commercial floors where maintenance must be performed during after hours. It is also perfect for residential floors especially when there are pets present or the floors get heavy use. Active Elements™ – Protect & Shine should be applied over the top of a base sealer such as Active Elements™ – Advance Seal. Coverage 500 – 1000 square feet per gallon Coverage variations depend on concrete surface porosity and amount of material applied. Drying Time Dry to Touch. 5-15 minutes Recoat 30 minutes Light traffic 1 hour Full Cure 5 hours Surface PreparationPrior to the application of Active Elements – Protect & Shine, the floor must be clean and dry. A previously applied base sealer must be fully cured. Application Tools Finish mop or floor finish applicator. Application Completely dampen the finish applicator with Active Elements – Protect & Shine and apply a very thin coat. As Active Elements – Protect & Shine is being applied it should make the floor look wet but not milky. If you are seeing a milky haze, reduce the amount of material being applied per square foot. Each successive coat should be applied perpendicular to the previous coat in order to reduce lap marks. ***For interior use only.*** Initial application on a floor — apply 4-8 thin coats. As a maintenance application — apply 1-2 thin coats. Thinning Do not thin. Clean Up Tools can be cleaned with soap and water. Storage and Shelf Life Do not allow to freeze. Shelf life of unopened product is approximately one year. Slip and Fall Precautions Water or other foreign substances will cause a floor coated with Floor Finish to become slippery. ALWAYS use a “Wet Floor” sign when moisture is present. Safety Do not breathe vapors. When using in confined or limited ventilation areas, use appropriate respirator to protect against breathing vapors. Avoid contact with skin; wear protective gloves and clothing. Always use eye protection such as goggles, face shield or safety glasses. Read Material Safety Data Sheet before using. First Aid Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids open. Seek medical attention. Skin Contact: Immediately remove contaminated clothing. Wipe excess from skin and wash with soap and water. Seek medical attention if irritation persists. Inhalation: Remove person to fresh air and provide oxygen if breathing is difficult. Seek medical attention. Moisture Vapor Emissions / Alkalinity Precautions All interior concrete floors not poured over an effective moisture vapor barrier/inhibitor are subject to possible moisture vapor transmission and related high levels of alkalinity that may lead to blistering and failure of the coating system. It is the coating applicator’s responsibility to conduct calcium chloride and relative humidity probe testing to determine if excessive levels of vapor emissions or alkalinity are present before applying any coatings. Warranty This warranty is made in lieu of all other warranties, either expressed or implied. Before application the User shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to replace said product. Any claim of defective product must be received in writing within one (1) year from date of shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from use of this product. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.

Outlast Q8 Log Oil 1 & 5 Gallon (7 Available Colors)

Effective exterior wood preservation starts with a broad-spectrum EPA registered Wood Preservative.Very few stain products can claim to prevent mold, decay and insect activity and offer water repellency at the same time. Here at Outlast Products, you will find the best log, timber and lumber preservative treatment solutions and waterproofing alternative systems to extend the life and beauty of any and all wooden structures from your decking to your log and timber home, fences with exposed end cuts, wood roofs and more.Outlast Q8 wood preservative is formulated to increase wood’s durability and enhance its resistance to weathering and aging. Expect vigorous water repellency without ever cracking or peeling off. This superior water repellent -waterproof alternative treatment is easy to apply with a pump sprayer to the point of refusal. When the wood cellulose is thoroughly saturated, the stain is self-leveling as drips blend away and lap marks are non-existent.Outlast’s wood preservative products range from log oil treatments to deck and cladding preservatives, and end-cut and fastener hole sealants that ensure deep absorption well beyond the lumber/log surface to ensure effective preservation and back-up rot control for commercially augmented Pressure Treated lumber. The use of Outlast Q8 will validate warranties on all pressure treated lumber including Outdoor and Wolmanized wood applications. Outlast Q8 Log Oil is American Wood Protection Association (AWPA) approved and specified in the M-4 Standard. Outlast Q8 Log Oil® is an EPA registered wood preservative specifically designed to control decay causing organisms (and mold, termites, powder post beetles) in log homes – even pressure treated. It provides unsurpassed water repellency and sheer trans-oxide color with one coat coverage. Outlast Q8 Log Oil® is a totally non-film forming exterior treatment that will never crack or peel. Unlike traditional surface coatings, Q8 penetrates deep into the log to provide guarantees protection and guaranteed no peeling or cracking.