Ultra Custom Pools

Item Tag: Mortise Lock

Amesbury Truth P2000 Active Single Point Mortise Lock 35/32 American Cylinder

We are an Authorized Distributor for Andersen, Larson, Marvin, Pella, GU Ferco, Hoppe, Emtek, Roto, Milgard, Peachtree, Weathershield, and many more. Shop our store for your door and window hardware needs. Customer Service Hours Monday-Friday 8am-4pm CST P2000 Active 35/92 Gearbox Only American Cylinder – No Faceplate Gearbox has a deadbolt and spring latch only – It is NOT a complete Multipoint lock (MPL) – CENTER LOCK BOX ONLYNOTE: This is the Lockcase Only – the faceplate rail is not includedThis mortise Lock case will replace the active gear box on Amesbury MPL with the same size and configuration. Amesbury has 3 different locks – Please compare measurements & InformationCylinder Type: American Backset: 1-3/8 inch (35mm)Handle PZ: 3-5/8 inch ( 92mm)Deadbolt Throw: 1 Inch (25.4mm)Faceplate Width: NONETo Change Handing / Latch Reversal:1. Extend Deadbolt and pull spring latch out2. Rotate to correct position3. Check function of lock before closing door

Mortsie Lock Single Point Active 60mm Backset Marvin, Caradco, Jeldwen doors

ingle point active lock (SPL) for Marvin Ultimate and other inswing doorsmanufactured 1/17/2000 to present.For mortise lock faceplate, see part # 395040Lock Body Type: American cylinderHandle spacing: 3-5/8 inch (92 mm) Center of handle to center of cylinderBackset: 2-3/8 inch (60 mm) Measured from door edge to center of handleBackset without Face plate (measures 2-5/16 as shown in 2nd image)Deadbolt throw: 1 inch (25.4 mm) TaperedPatent NO. 6,209,931Single point locks used by Marvin, Caradco, Jeldwen and othersPriced and sold each.NOTE: Does Not include faceplate or Strike, lock body onlyScrew between Latch and Deadbolt is a # 6 Flat head, not includedChange Handing:1. Insert screw driver into slot behind latch2. Pull down on handing release, latch pops out3. Rotate latch and push back into lock caseALWAYS Check Function of lock before closing doorOperation:1. Lift handle to engage2. Turn Thumbturn or key to extend the deadbolt

Hoppe Mortise Lock Single Point Mortise Lock 1″ Deadbolt Throw 2-3/8″ Backset

This will NOT work for replacing the lock body on multipoint lock units. This is a single point lock only. Hoppe Mortise Lock, Manual Gear, Single Point with 1 inch (25mm) Deadbolt throw Used by Caradco, Jeldwen, Norco and others. Stainless face plate 5/8 (16mm) inch wide x 10-7/8 inches long Face plate screw holes are spaced 10-1/8 inch Backset: 2-3/8 inch (60mm) – distance from edge of face plate to center of lock handle All Current Model Single Point Locks from HOPPE w/ Rotation Limiter (Lever is fixed and does not move after door is locked) 11517463 – 35mm backset, 14mm deadbolt throw, 16mm faceplate with radius ends 11517475 – 35mm backset, 25.4mm deadbolt throw, 16mm faceplate with radius ends 11517487 – 45mm backset, 14mm deadbolt throw, 16mm faceplate with radius ends 11517499 – 45mm backset, 25.4mm deadbolt throw, 16mm faceplate with radius ends 11517505 (this listing) – 60mm backset, 25.4mm deadbolt throw, 16mm faceplate with radius ends 11517517 – 70mm backset, 25.4mm deadbolt throw, 16mm faceplate with radius ends 11517529 – 35mm backset, 25.4mm deadbolt throw, 16mm faceplate with square ends (Please contact office if needing one of the locks not currently linked to our site) Latch handing may be changed by pulling out or inserting small screwdriver into small hole in back of latch and pushing forward, twist latch and release. See linked article below. HOPPE Screws for Installation: 8785695 – Screw 1-3/8″ ( 35mm ) 8mm Head – Stainless Steel 8785687 – Screws, 3/4″ (20mm ) 8mm Head – Stainless Steel Helpful Articles How To Drill Out A HOPPE Mortise Lock If The Dead Bolt Doesn’t Retract How to Change the Handing (Reverse the Slope of the Latch) on a HOPPE Lock

Amesbury Truth P2000 Active Single Point Mortise Lock 60/92 American Cylinder

We are an Authorized Distributor for Andersen, Larson, Marvin, Pella, GU Ferco, Hoppe, Emtek, Roto, Milgard, Peachtree, Weathershield, and many more. Shop our store for your door and window hardware needs. Customer Service Hours Monday-Friday 8am-4pm CST P2000 Active single point lock (SPL) 60/92 GearboxThe Single Point Lock (SPL) has a deadbolt and spring latch only – It is NOT a Multipoint lock (MPL)This mortise Lock case will replace the active gearbox on Amesbury MPL with the same size and configuration. Amesbury has 3 different locks – compare informationCylinder Type: AmericanBackset: 2-3/8 inch (60mm)Handle PZ: 3-5/8 inch ( 92mm)Deadbolt Throw: 1 Inch (25.4mm)Faceplate Width: 25/32″ (20mm)Faceplate Markings: LF2200Lock Depth: 2-1/2 inches (64mm)To Change Handing / Latch Reversal:1. Extend the Deadbolt and pull the spring latch out2. Rotate to correct position3. Check the function of the lock before closing the doorInstallation Note:The T-20 torx Star bit screws require 12-13 pounds of torque

Hoppe Mortise Lock Single Point Mortise Lock 1″ Deadbolt Throw 1-3/8″ Backset

We are an Authorized Distributor for Andersen, Larson, Marvin, Pella, GU Ferco, Hoppe, Emtek, Roto, Milgard, Peachtree, Weathershield, and many more. This is a single point lock and it is not interchangeable with the lock body on a HOPPE multipoint lock, nor can it be used to repair or provide parts for a multipoint lock.

Amesbury Truth P2000 Active Single Point Mortise Lock 45/92 European Cylinder

We are an Authorized Distributor for Andersen, Larson, Marvin, Pella, GU Ferco, Hoppe, Emtek, Roto, Milgard, Peachtree, Weathershield, and many more. Shop our store for your door and window hardware needs. Customer Service Hours Monday-Friday 8am-4pm CST Premier P2000 gear box for multipoint-locks with 1-3/4″ (45mm) backsetUsed on active doors with 5/8″ (16mm) or 25/32″ (20mm) faceplatesNO FACEPLATE, this is the gearbox only, used to repair or replace broken gearsBackset: 1-3/4″ (45mm)Handle to Cylinder spacing: 3-5/8″ (92mm)Cylinder Type: Euro / Profile VersionLockcase bodies are available in 3 backsets1-3/8 inch (35mm)1-3/4 inch (45mm)2-3/8 inch (60mm)